266
Program description - Basic settings
This option is available on both transmit-
ter types.
Use the selection keys on the left or right
four-way button to scroll to the »Basic set-
tings« menu option in the multi-function menu:
MP3 player
Basic settings
Servo display
Servo test
Code lock
Info display
Tap briefly on the centre SET key of the right four-way
button to open this menu option:
Battery type
Battery warning
Touch Sense
Top LCD Contrast
Lith.
Display light
2
3.60V
0
unlim.
Basic settings
Vario Vol
Beeps Vol
Power-on beep
yes
Power on warn.
unlim
BT Headset
OFF
0/0
ID PAIR
OFF
BT Volume
8
Voice Vol –––5
–––7
–––7
Own
Stick mode 1
Modulation HoTT
DSC Output
PPM10
Pitch min back
Bottom LCD Contr.
0
SEL
SEL
fr
fr
fr
DATA sel Telemetry
Basic settings are made in this menu. Transmitter-
specific settings, such as volume regulation for acous-
tic signals and voice messages output via the built-in
speaker or headset connector, the owner’s name,
country setting and even specifications for new model
memories. The settings made in this menu on the lines
…
• “Stick mode”,
• “Modulation”,
• “DSC Output” and
• “Pitch min”
… therefore have no influence whatsoever on already
existing model memories; instead, they are only de-
faults which are automatically adopted into newly
initialized model memories and can be changed there
individually at any time in the »Basic settings, model«
and »Helicopter type« menus. A change to the “Pre-
set” settings in value fields of this menu therefore only
affects those model memories created new at a later
time.
Note:
The settings in this menu are only specied
once in the entire transmitter. Therefore, after
opening this menu in another model memory,
the last valid settings always appear.
Programming procedure
Select the desired line with the selection keys of
the left or right four-way button then tap the centre
SET key of the right four-way button. The value in the
field now displayed in inverse video can be changed.
After a change has been made, the entry can be con-
cluded with another tap on the centre SET key of the
right four-way button or the centre ESC key of the left
four-way button.
Voice volume / Vario volume / Beeps volume
–––7
–––3
–––7
SEL
SEL
fr
fr
fr
Basic settings
Vario Vol
Beeps Vol
Voice Vol
Own
These three lines can be used to individually set the
volume of the three groups of acoustic signals and
voice messages. This involves selection from among
a total of three variants, whereby the variants two and
three offers option for individually regulating the volume
even after leaving this menu.
Pre-setting a value
Use the selection keys on the left or right four-way but-
ton to move the marker frame to the desired value field
in the column above the left SEL at the display’s lower
edge then briefly tap the centre SET key of the right
four-way button. The desired volume for the selected
group can be specified in increments between 0 and
10 in the value field now displayed in inverse video by
using the selection keys of the left or right four-way
button. Another tap on the centre SET key of the right
four-way button or the ESC key of the left four-way
button will conclude the process.
Following a simultaneous tap on the or keys
of the right four-way button (CLEAR), the display will
return to its “7” default value.
via proportional control
Use the selection keys on the left or right four-way but-
ton to move the marker frame to the desired value field
in the column above the right SEL label at the display’s
lower edge then briefly tap the centre SET key of the
right four-way button. The message shown below will
then appear in the display:
Basic settings
Basic transmitter settings
mc
16 20
To Next Page
Loading...
Need help?
General
