79
Program description - Base setup models | Winged models
signals of them explicitly allocated memory model.
One, possibly unintentional, operating on an unal-
located model space is not therefore possible.
• The HoTT synchronization behavior of a copied or
imported model memory depends on several fac-
tors. For details, refer to the appropriate section.
• The respective HoTT synchronization type of
“bound” model memory is left of the synonym
for the receiver type in the menu “Model select”
recognizable:
“Model” -specific bound receiver with an “M” and
“global”, ie Transmitter far, bound receiver with a
“G”.
As an illustration of this, the model memory 01, 03
and 04 with model-specific and model memory 02
are in the figure below exemplified with transmitter-
specific binding:
03
04
05
STARLET
BELL47G
06
MR12
M–––
free
free
01
GRAUBELE
MR12
02
ULTIMATE GR12
Module
The
mc-16 HoTT and mc-20 HoTT are fitted as
standard with a HoTT RF module. However, it is also
possible to switch to a non-Graupner external RF
module by software, if such a module is connected
to the transmitter. This is accomplished by using the
Select buttons of the left or right-hand four-way button
to move to the left, to the “Module select” value field:
tion selection so a change to another line can be af-
fected.
Binding type
Note:
This menu item is only visible as long as no
receiver is bound to the currently active model
memory.
An “unbound” model memory can be changed at any
time from the default preset memory specific HoTT
transmitter-specific synchronization, and vice versa.
So If necessary, change the line “Binding Type” and
press the SET button to the right four-way button.
1
GRAUBELE
SEL
Module HoTT n/a
n/a
Mod.name
Stick mode
Binding type
Base setup model
Model
... And change with the selection keys of the left or
right four-way button, the setting in “global” (or vice
versa):
1
GRAUBELE
SEL
Module HoTT n/a
n/a
Mod.name
Stick mode
Binding type
Base setup model
Global
Note:
•
“Global”, ie specific sender, receiver
bound to respond to the signals of all
model memories “their” station, which is
why firmware version V1101 for safety reasons, a
model change only after switching off the receiving
system is possible.
• “Model” -specific bound receivers respond only to
1
n/a
bind
BD1
GRAUBELE
BD2
Rcv Ch Map R12
n/a
HoTT
Mod.name
Stick mode
module
Base setup model
HoTT
To be able to connect to the transmitter, Graupner
HoTT receiver must be connected to at least one
model memory “of their” Graupner HoTT transmitter.
This process is commonly referred to by the English
term “binding” and can be repeated anytime. This
“binding” of a receiver is by default always memory-
specic, but may at any time and for any unbound
model memory of a transmitter in the menu that
appears row “binding type”, see above, to transmitter
specic, and can be reversed, changed.
Important notices:
•
During the binding procedure be sure
the transmitter’s antenna is always far
enough away from the receiver’s anten-
na. To be on the safe side, keep them at least
one meter apart. Otherwise there is a risk of a
faulty connection to the return channel and
malfunctions will result.
• Pay close attention to the correct power sup-
ply of the receiving system. Too low supply
voltage while responding the LEDs of the re-
ceiver as described below on your Binding ef-
fort, yet there is no proper HoTT Synchroniza-
tion.
• When binding additional receivers, note that
any other – switched on – receivers already
bound to the transmitter will fall into Fail safe
mode during the transmitter-side “binding” pe-
riod.
To Next Page
Loading...
Need help?
General
