Krone Swadro 2000

To Next Page

To Previous Page

Maintenance - hydraulic system

220

Pos: 40.33.5.15 / BA/Wartung/Loa d-Sensing/SW 2 000/Bild Not-H and-Betätigung Beispiele Sw adro 2000 @ 61\ mod_12984655 42770_78.doc @ 566821 @ @ 1

In order to perform a function (e.g. moving the rotor arms from working to transport

position), activate the appropriate valves.

SW2000064_1

Y24Y2

Y25

Y5 Y4 Y7Y6

Y26

Y11Y10

Y9 Y8

Y16

Y12

Y14

Y18

Y20

Y22

X1)

X2)

Fig. 157

Pos: 40.33.5.16 / BA/Wartung/Loa d-Sensing/SW 2 000/Not-Ha nd-Betätigung X1 / X2 @ 61\mod_ 12984717812 48_78.doc @ 567037 @ @ 1

X1) = Valve shown in direction of travel at the rear

X2) = Valve shown in direction of travel at the front

Pos: 40.33.5.17 / BA/-----Seiten umbruch------ @ 0\mod_1196175 311226_0.doc @ 4165 @ @ 1

Main Page

Table of Contents2
Table of Contents3
Foreword10
Introduction11
- General Description of the Machine11
- Validity11
- Identification Plate11
- Information Required for Questions and Orders12
- Intended Use13
- Road Traffic Regulations and Operating Permits13
- Machine Overview14
- Technical Data15
Safety16
- Identifying Symbols in the Operating Instructions16
- Identification of the Hazard Warnings16
- Safety Instructions and Accident Prevention Regulations18
- Hitched Implements19
- PTO Operation20
- Hydraulic System21
- Tyres21
- Maintenance21
- Unauthorised Conversion/Modification and Spare Parts Production22
- Inadmissible Modes of Operation22
- Position of the Adhesive Safety Stickers on the Machine23
- Introduction23
- Safety Instructions on the Machine23
- Position of the General Information Labels on the Machine26
Commissioning29
- First Installation29
- Fitting the Protective Frames/Hoop Guards on the 6 Rotors30
- Requirements on the Tractor32
- Preparations on Tractor32
  - Adjusting the Lower Suspension Arms32
Table of Contents33
- Electrical Power Supply33
- Mounting Onto the Tractor33
- PTO Shaft34
  - Length Adjustment34
- Height of Tractor Lower Suspension Arms34
KRONE Operation Terminal Gamma35
- Mounting the Control Unit36
  - Electrical Power Supply37
- Overview38
- Description of the Keys39
- Operational Readiness41
- Display Areas on the Screen42
- Road Travel" Basic Screen48
- Basic Screen "Lifting the Rotors49
- Basic Screen "Width Adjustments54
- Basic Screen "Working Height57
  - Adjusting the Working Height of the Rotors57
  - Rotor Height Automatic Mode58
- Menu Level59
  - Short Overview59
  - Bringing up a Menu Level60
- Main Menu 1 - Settings62
- Main Menu 2 - Counters68
  - Menu 2-2 "Total Counters71
- Main Menu 3 „Manual Operation72
- Main Menu 4 - Service79
- Main Menu 5 - Information90
- Main Menu 6 "Technician91
  - Alarm Message92
- Alarm Messages93
Control Unit - Auxiliary Control99
- Mounting100
  - Electrical Power Supply101
- Overview of Auxiliary Control102
- Operational Readiness104
- Lowering the Rotors from Transport to Headland Position105
  - Lowering All Rotors to Headland Position105
- Lowering the Rotors from the Headland Position to the Working Position106
Table of Contents108
- Raising the Rotors from the Working Position to the Headland Position108
- Raising All Rotors from the Headland Position to the Transport Position109
- Adjusting the Working Width110
  - Adjust the Front Working Width110
- Alarm Messages110
- Malfunctions - Causes and Remedies110
KRONE ISOBUS-Terminal CCI 100111
- Installing the Terminal into Cabin112
- ISOBUS Short Cut Button113
- Display Areas on the Screen120
  - Status Line Area (I)121
  - Displays in the Main Window (II)122
- Basic Screen "Width Adjustments125
  - Working Width125
  - Swath Width126
- Basic Screen "Working Height127
  - Adjusting the Working Height of the Rotors127
- Basic Screen „Lifting the Rotors128
- Menu Level135
  - Brief Overview135
  - Calling up the Menu Level136
- Main Menu 1 "Settings137
  - Menu 1-2 "Zero Calibration Rotor Height" (Rotor Height Display Option)138
  - Menu 1-3 "Overlap139
- Main Menu 2 "Counters140
  - Menu 2-1 "Customer Counter141
  - Menu 2-2 "Total Counters144
- Main Menu 3 „Manual Operation145
- Main Menu 4 "Service151
- Main Menu 5 "Information162
- Main Menu 6 „Fitter163
- Main Menu 9 "ISO Settings Info164
  - Menu 9-1 "Softkeys ISO Terminal165
  - Menu 9-2 "Switching between Terminals166
- Alarm Message167
- Alarm Messages168
ISOBUS Operation173
- Attaching the ISOBUS Terminal174
  - Connection Terminal to Tractor174
  - Connection Tractor to Machine174
- Differing Functions to KRONE ISOBUS Terminal CCI175
  - Menu 4-7 "Diagnostics Auxiliary (AUX)176
- Main Menu 9 "ISO Settings Info177
  - Menu 9-1 "Softkeys ISO Terminal178
  - Menu 9-2 "Switching between Terminals179
- ISOBUS „Auxiliary"-Function (AUX)180
  - Example of a Joystick Assignment for Fendt (Default Setting)182
Start-Up183
- Mounting Onto the Tractor183
Table of Contents184
- Hydraulics184
  - Special Safety Instructions184
  - Connecting the Hydraulic Lines185
- Lighting Connection186
- Connecting the Electrical Controls187
- Compressed Air Connections for the Compressed Air Brake188
  - Moving the Machine Without Tractor189
- Hydraulic Brake (Export)189
- Install the PTO Shaft190
- Parking Brake191
Driving and Transport192
Operation193
- Overload Protection193
- From Transport into Working Position194
  - Removing the Tine Guards from the Tine Tips194
- Lowering the Rotor Arms into Working Position194
- Adjusting the Raking Height195
- Auxiliary Steering196
  - Move Auxiliary Steering to Centre Position196
- Travelling on an Incline197
- Travelling Speed und Drive Speed197
- Switching from Working Position to Transport Position198
- Raising the Rotor Arms to Transport Position198
- Protecting the Tine Tips (Transport Position and Swather Switched Off)199
- Parking200
Settings202
- To Adjust the Rotor Running Gear202
- Setting the Lifting Height in Headland Position203
- Adjustable Throttles204
Maintenance205
- Special Safety Instructions205
- Spare Parts205
- Tightening Torques206
- Tightening Torques (Countersunk Screws)207
- Testing the Screws on the Tines207
- Tyres208
  - Checking and Maintaining Tyres208
- Replacing the Tine Arms(in Case of Repair)210
- Position of the Sensors212
  - Adjusting the Sensors214
    - Namur Sensor D = 12 MM214
    - Namur Sensor D = 30 MM214
Maintenance - Hydraulic System215
- Load-Sensing Connection216
- Adjusting the Hydraulic System217
- Emergency Manual Activation217
- Preparing the Machine for Road Travel (in Emergency Manual Mode)219
- Hydraulic System Circuit Diagrams224
- High-Pressure Filter226
Maintenance - Lubrication Chart227
- Special Safety Instructions227
- PTO Shaft227
Maintenance - Lubrication Chart228
- Lubrication Chart228
Maintenance - Gearbox230
- Filling Quantities and Lubrication Designations for Gearboxes230
- Rotor Gear231
- Angular Gearbox231
Maintenance - Brake System232
- Air Filter for Pipe233
- Compressed-Air Reservoir234
Special Equipment235
- Tine Loss Safeguard235
Placing in Storage236
- Special Safety Instructions236
- At the End of the Harvest Season237
- Before the Start of the New Season238
- Special Safety Instructions238
Malfunctions - Causes and Remedies239
- Special Safety Instructions239
- Electrical Circuit Diagram241

Krone Swadro 2000 - Page 220

Table of Contents

Related product manuals