EasyManuals Logo

Krone Swadro 2000 User Manual

Krone Swadro 2000
262 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #53 background imageLoading...
Page #53 background image
KRONE operation terminal Gamma
53
Pos: 16.8.25 /Üb erschriften/Üb erschriften 3/A-E/ Anheben aller Kreisel von Vorg ewendestellung- i nT ransportst ellung @ 38\m od_1267427704 146_78.doc @ 3 55171 @ 3 @ 1
6.7.5 Raising All Rotors from the Headland Position to the Transport Position
Pos: 16.8.26 /B A/Info-Center/Sch wader/Bedi eneinheit - Komfort /SW 2000/Gru ndbild 1 Kreisel aushebung/Hin weis Während de sEi nfahrens der Arbeistbreitenz ylinders vorahre n @ 38\mod_1 26742834224 0_78.doc @ 3 55243 @ @ 1
Note
While the working width cylinder retracts, drive at low speed to set the front supporting wheels
in the correct position.
Pos: 16.8.27 /B A/Info-Center/Sch wader/Bedi eneinheit - Komfort /SW 2000/Gru ndbild 1 Kreisel aushebung/Anhe ben aller Kreis el von Vorgew endestellung in Tr ansportsellung S W 2000 @ 23\ mod_1240294 136022_78.doc @ 237306 @ @ 1
By pressing the key for approx. 1.0 seconds, all rotors are raised to the transport position.
Pos: 16.8.28 /B A/Info-Center/Sch wader/Bedi eneinheit - Komfort /SW 2000/Gru ndbild 1 Kreisel aushebung/Hin weis keine einzel nen Kreisel (Vorg ewendestellu ng/T ransportst ellung) anhebe n @ 38\mod_1 267428085943_ 78.doc @ 355219 @ @ 1
Note
Individual rotors cannot be lowered from the headland position to the transport position.
Pos: 16.8.29 /B A/Info-Center/Sch wader/Bedi eneinheit - Komfort /SW 2000/Gru ndbild 1 Kreisel aushebung/Hin weis Beschreib ungR eihenfolge des Klappvorga nges @ 38\mod _1267427907 286_78.doc @ 3 55195 @ @ 1
Note
First the hydraulic cylinders retract the setting for working width and swath width. Then the
supporting wheels are folded in. Finally, the rotors are raised.
Pos: 16.8.30 /B A/Info-Center/Sch wader/Bedi eneinheit - Komfort /SW 2000/Gru ndbild 1 Kreisel aushebung/Kr eiselarme heben nic ht in Transports ellung @ 23\ mod_12402952 39897_78.doc @ 237327 @ @ 1
If the rotor arms do not raise into the transport position, there are two possible causes (a
corresponding error message appears in the display).
L
?
2
R
?
Check the position of the supporting wheel (if necessary, drive the machine
forwards approx. 2m).
3
L
?
4
R
?
Position of outrigger arm too high or too low.
Lower or raise the main frame.
Park the machine on level ground.
Pos: 16.9 /BA/---- -Seitenumbruch--- --- @ 0\mod _1196175311 226_0.doc @ 416 5@ @ 1

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Krone Swadro 2000 and is the answer not in the manual?

Krone Swadro 2000 Specifications

General IconGeneral
BrandKrone
ModelSwadro 2000
CategoryFarm Equipment
LanguageEnglish

Related product manuals