How to troubleshoot power issues with my SciCan Laboratory Equipment?
If your SciCan Laboratory Equipment doesn't power on, check that it's plugged into a properly grounded outlet and the power cord is firmly connected at the rear. Try a different circuit. Power the unit off for 10 seconds, then back on. Also, check the condition of the line circuit breaker or fuse.
What to do if my SciCan Statim 2000 displays 'REFILL RESERVOIR'?
If your SciCan Laboratory Equipment displays 'REFILL RESERVOIR' and won't start, it means the water level in the reservoir is low. Simply refill the reservoir.
Why does my SciCan Statim 2000 Laboratory Equipment say 'WATER QUALITY IS NOT ACCEPTABLE'?
If the SciCan Laboratory Equipment displays 'WATER QUALITY IS NOT ACCEPTABLE' and won't start, it's likely due to using improperly distilled water. Empty the reservoir and refill it with steam-process distilled water that has less than 5 ppm total dissolved solids (conductivity less than 10 µS / cm). Use a water conductivity meter to check the water quality before refilling.
How to fix SciCan Statim 2000 Laboratory Equipment that does not power ON?
If your SciCan Laboratory Equipment isn't powering on, make sure it's plugged into a properly grounded outlet and that the power cord is firmly seated at the rear of the machine. Try using a different electrical circuit. Power the unit OFF for 10 seconds, then power it back ON. Also, check the condition of the line circuit breaker or fuse.
What to do if there is water under my SciCan Statim 2000 Laboratory Equipment?
If you find water under the SciCan Laboratory Equipment during operation, it could be a leaking cassette. Check the cassette seal for misalignment or damage and replace it if necessary. Be careful, as the metal parts will be hot, and the cassette will contain hot steam. Attempt another cycle.
What does 'Drying interrupted – LOAD NOT STERILE' mean on my SciCan Statim 2000?
If you see the 'Drying interrupted – LOAD NOT STERILE' message on your SciCan Laboratory Equipment, it likely means the STOP button was pressed during the drying phase. Repackage the instruments if necessary, and rerun another sterilization cycle.
How to improve drying in SciCan Statim 2000?
If instruments are not drying in your SciCan Laboratory Equipment, ensure the cycle completes fully. Proper loading of instruments in the cassette is important. Verify the unit is level. Inspect air filters and replace them if dirty. Clean the cassette's interior and apply Stat-Dri / Stat-Dri Plus drying agent. Also, check the exhaust tube for any kinks.
What to do if there is water under SciCan Statim 2000 Laboratory Equipment?
If you find water under your SciCan Laboratory Equipment, it's likely due to a leaking cassette. First, check the cassette seal for any misalignment or damage; if you spot any, replace the seal. If water continues to drip from the unit's underside during operation, inspect the cassette seal again for misalignment or damage and replace it if needed. Should the leak persist, turn the unit OFF, remove and unload the cassette, unplug the unit, and contact your dealer.
List of STATIM specific and generic tools required for servicing the unit.
Schedule and parts required for annual servicing of STATIM 2000/5000/G4 units.
Guidelines for daily, weekly, and semi-annual maintenance to keep STATIM in good order.
Procedures for dielectric strength test (Hi-Pot) and protective bonding impedance test.
Functional checks recommended when the cause of a problem is unknown or a cycle fault is unavailable.
Guidance on using unit software and service menus for diagnosis and information gathering.
Explanation of different types of cycle fault formats and their descriptions.
Step-by-step guide for calibrating STATIM 2000 non S units with Rev 3.x or 4.x controller boards.
Calibration procedure for STATIM 2000/5000 non S units with Rev 2.x/5.x boards and R1.xx/R2.xx software.
Calibration procedure for STATIM 2000/5000 non S units with Rev 6.x boards and R4.xx/R5.xx software.
Calibration procedure for STATIM 2000/5000 non S units with Rev 7.x boards and R6.xx software.
Calibration procedure for STATIM 2000/5000 G4 non S units with Rev 7.x boards and R7.xx/SL00R1.xx software.
Calibration procedure for S-class STATIM 2000 units with Rev 2.x/5.x boards and R1.xx/R2.xx software.
Calibration procedure for S-class STATIM 2000 units with Rev 6.x boards and R4.xx/R5.xx software.
Calibration procedure for S-class STATIM 2000 units with Rev 7.x boards and R6.xx software.
Calibration procedure for S-class STATIM G4 units with Rev 7.x boards and R7.xx/SL00R1.xx software.
Information on identifying and working with STATIM controller boards.
Step-by-step instructions for removing the controller board assembly from STATIM units.
Identifies the three types of pumps used in STATIM units and notes on interchangeability.
Procedure to test water pump flow for all STATIM unit types.
Details on filter maintenance for STATIM 2000/2000S units, including internal and in-line filters.
Steps to perform maintenance on internal filters located within the pump assembly.
Guide to replacing pump tubes to ensure correct water delivery for sterilization cycles.
Steps to check the conductivity sensor's functionality and diagnose problems.
Steps to resolve the "WATER QUALITY NOT ACCEPTABLE" message, potentially due to EMI.
Information on the two types of solenoid valves used in STATIM units.
Steps to inspect and repair the Type B solenoid valve assembly.
Information about pressure transducers used in STATIM S models.
Methods for identifying and checking the pressure transducer types and their output.
Procedure for checking the transducer's functionality and diagnosing faults.
Guide to aligning the probe bracket and chamber thermocouple using a jig or manually.
Steps to troubleshoot common issues with the Data Logger, like MSD detection errors.
Procedure for filling the reservoir with steam-process distilled water.
Steps to prime the STATIM pump before initial use or after servicing.
Final steps before initial use, including running cycles and cleaning the cassette.
Steps for powering up and running tests on the installed STATIM unit.
General| Water Consumption | Approximately 60 ml per cycle |
|---|---|
| Warranty | 1 year |
| Sterilization Temperature | 135°C (275°F) |
| Sterilization Time | 3.5 minutes |
| Sterilization Method | Steam |
To Next Page
