What does 'HCT indicator calibration: connect saline solution' mean on sorin XTRA Medical Equipment and how to fix it?
R
Rhonda WilsonSep 3, 2025
The saline solution might be missing. Spike a saline solution bag, then press PLAY to resume. The wash line might be clamped. Remove the clamp, then press PLAY to resume. To perform the HCT indicator calibration later, press DELAY CALIBRATION. If you intend to proceed with HCT indicator calibration, switch the machine off and on again, then press RETAIN. Make sure to do this before pressing the LOAD PUMP button.
E
ellen87Sep 1, 2025
What does 'Memory not functioning. Part of the data has been lost' mean on sorin XTRA Medical Equipment?
L
landryeddieSep 1, 2025
The machine will continue working anyway, but it is recommended to call the authorized technical service. Press X to clear the warning message and continue.
A
April MurphyAug 31, 2025
How to resolve 'Inconsistent vacuum mode' error on Sorin Medical Equipment?
C
Caitlin FloresAug 31, 2025
The vacuum pump is set on a different mode vs. the one required by the wake up protocol. Press CHANGE VACUUM MODE to switch to the wake up mode. The pump will be automatically turned off. Press I/O on the vacuum pump to turn it back on and press PLAY to resume.
B
beckyrandallAug 29, 2025
What to do if Sorin Medical Equipment shows 'Fluid loss in centrifuge: Biohazard risk'?
H
Heather BlackAug 29, 2025
Open the centrifuge lid and the centrifuge arm, check that the bowl is not leaking, and make sure that all clamps of bowl set and waste bag are open. If there is a leak, press X to exit and display the current screen, unload the pump loop and remove the disposable. Clean the centrifuge housing and sensor, install a new disposable, start a new case and eventually reopen the case from the Tally Screen. If there is no leak, clean the ‘Centrifuge Fluid Loss’ sensor with a dry cloth, make sure the bowl set is mounted properly, close the centrifuge lid and press X to exit and display the current screen. You may decide to disable the sensor and the related alarm for the current case by pressing DISABLE ALARM.
B
Brittany DavisAug 27, 2025
What causes 'Pump loop loading failed' on sorin XTRA Medical Equipment and how to resolve it?
H
Henry KaufmanAug 28, 2025
The machine cannot properly load the pump loop. If the pump loop is blocking the rotor, manually remove it. Check for any eventual damage to the pump loop and, if present, replace the disposable. If the pump loop is not damaged, manually seat it and press PLAY to resume. If the rotor is blocked by any other object, remove it, then press PLAY to resume.
K
Kristina HendrixAug 26, 2025
What to do if sorin XTRA displays 'Reservoir empty. Bowl not filled'?
S
Sandra StantonAug 26, 2025
If the reservoir is not empty, check the air sensor, make sure the tubing going to the bowl is seated properly inside the sensor and the fill line is not occluded/clamped. Press FILL to resume. If this is the last cycle, press LAST BOWL (only if enabled) to automatically complete the case. You can also press CONCENTRATE to start the concentration phase or RETURN (only if present) to return the blood into the reservoir. If the bowl is sufficiently packed with RBCs, you may decide to press WASH to proceed to the Wash phase or 2XWASH to use twice the saline solution.
M
michaelnelsonAug 25, 2025
How to fix 'Pump rotor out of position' error on Sorin Medical Equipment?
H
Heidi DixonAug 25, 2025
Open the centrifuge lid and check the position of the pump rotor: open the white lever, push the pump rotor fully down, turn the pump rotor to align the white lever with the slot in the metal shaft, close the white lever into the slot, and make sure the white lever is completely down. Close the centrifuge lid and press PLAY to resume.
N
nelsontoddAug 22, 2025
What to do if the Sorin Medical Equipment shows 'Wash bag empty'?
J
Jon MartinezAug 22, 2025
The sensor detects air in the wash line. The wash line might be clamped or occluded. Remove the occlusion and press PLAY to resume. The saline solution bag might be empty. Spike a new saline solution bag and press PLAY to resume.
To Next Page
General
