February, 2008
6-15
WorkCentre 5225, 5230
IOT NVM List
General Procedures
Launch Version
Chain 740-xxx Chain 751-xxx 752-xxx Chain 753-xxx Procon
Table 10 Procon
Chain-
Link
Name Default Range 1 Count Remarks
740-529 SL_CRU/LL_CRU Selection for Third Party Con-
sumables
0 0~99 - 0: SL (standard life) Drum CRU, 1: LL (long life) Drum CRU
751-005 Toner Empty on Toner Cartridge (for CRUM Read) 0 0~1 - 0: Toner Cartridge is not empty 1: Toner Cartridge is empty
751-012 Enable Drum Life Adjust 1 0~1 1 1: Perform subtraction for DRUM CRUM data (DRUM life threshold value)
0: Do not perform subtraction for DRUM CRUM data (DRUM life threshold value)
751-709 Toner Refill History in Customer Mode A 0 0~99 1
752-003 ATC OUT First 2Dig 3 00~19 1
Not available
752-003 ATC OUT Last 2Dig 70 00~99 1
752-006 ATC Target First 2Dig - 00~19 1
Not available
752-006 ATC Target Last 2Dig - 0~99 1
752-007 Result of ATC Check - 0~4 0=Low, 1=Normal, 2=High, 3=False, 4=Abnormal end
752-503 Humidity Sensor Judge - 0~1 1 Not available
752-504 Temperature Sensor Judge - 0~1 1 Not available
752-509 Toner Empty 0 0~1 1 0: Normal, 1: Abnormal
752-523 Current Humidity (%) - 0~99 1 Not available
752-541 Current Temperature [deg.C] - 0~99 1 Not available
752-725 First 2Digits of LD2 - 00~19 1
Not available
752-725 Last 2Digits of LD2 - 00~99 1
752-747 Barcode LD_Ref 77 0~99 1 Default value that is the coefficient of Barcode LD
752-747 Barcode LD_Ref 0 0~2 1
752-748 Barcode LD_H 78 0~99 1 Maximum value that is the coefficient of Barcode LD
752-748 Barcode LD_H 0 0~2 1
752-749 Barcode LD_L 76 0~99 1 Minimum value that is the coefficient of Barcode LD
752-749 Barcode LD_L 0 0~2 1
752-756 Barcode_Switch 0 0~2 1 Barcode LD operating mode:
0: follows mode selected by the controller
1: forced ON
2: forced OFF
752-843 Accumulated Dispense Time in M/C
Last Two Digits
0 0~99 100 ms Because the value indicates accumulated time in M/C, initialization of the value is not
permitted.
752-843 Accumulated Dispense Time in M/C
Middle Two Digits (2)
0 0~99 100 ms Because the value indicates accumulated time in M/C, initialization of the value is not
permitted.
752-843 Accumulated Dispense Time in M/C
Middle Two Digits (1)
0 0~99 100 ms Because the value indicates accumulated time in M/C, initialization of the value is not
permitted.
752-843 Accumulated Dispense Time in M/C
First Two Digits
0 0~99 100 ms Because the value indicates accumulated time in M/C, initialization of the value is not
permitted.
752-844 Level of Remaining Drum Life Amount 100 0~100 1%
To Next Page
Loading...
Need help?
General
