Krone Big Pack 890 - Page 348

348
Main menu 6 (Technician) ................................ 129
Maintenance ............................................... 40, 267
Maintenance - Brake System ........................... 289
Maintenance - lubrication ................................. 295
Malfunctions - Causes and Remedies .............. 323
Malfunctions on the knotter .............................. 325
Manoeuvring the machine without hydraulic
connection ...................................................... 73
Manual mode .............................................. 84, 144
Manual mode basic screen ....................... 144, 146
Menu 1-1 Correction value bale length ..... 100, 158
Menu 1-2 Knotter signal............................ 101, 159
Menu 1-3 Sensitivity of direction display .......... 102
Menu 1-3 Sensitivity of the direction display .... 160
Menu 1-4 ........................................................... 103
Menu 1-5 Central lubrication .................... 106, 162
Menu 1-6 Knotter blowing ......................... 108, 164
Menu 1-6-1 Strokes / blow ........................ 109, 165
Menu 1-6-2 Bales / blow ........................... 110, 166
Menu 1-6-3 Blow time ....................................... 111
Menu 1-6-3 Blowtime ........................................ 167
Menu 1-7 Unit of measurement ........................ 112
Menu 2-1 Customer counter ..................... 114, 169
Menu 2-2 Total bale counter ..................... 116, 171
Menu 4-2 Manual sensor test ........................... 173
Menu 4-2 Manual Sensor Test ......................... 118
Menu 4-4 Manual actuator test ................. 124, 179
Menu level (brief overview) ............................... 155
Menu level (short overview) ................................ 96
Menüebene aufrufen ......................................... 156
Mounting onto the Tractor ............................ 56, 59
Mounting the control unit .................................... 78
Moving ................................................................ 72
MultiBale equipment (optional) ......................... 219
O
Oil Level Check and Oil Change Intervals
(Gearboxes) .................................................. 282
Oil quantities and designations for the compressor
................................................................ 23, 282
Oil quantities and designations for the on-board
hydraulic system ..................................... 23, 282
On-board hydraulic system .............................. 275
Operation ......................................................... 197
Overload coupling on flywheel ......................... 322
P
Packer drum drive ............................................ 216
Packer gearbox ................................................ 284
Park
ing ............................................................... 74
Parking brake ............................................... 48, 74
Personnel Qualification and Training ................. 35
Pick up ............................................................. 198
Pick-up drive over gearbox (without XC cutting
system) ........................................................ 218
Pick-up drive with XC cutting system ............... 218
Pick-up gearbox ............................................... 286
Placing in Storage ............................................ 319
Pneumatic brake cylinders ............................... 292
Position needles – checking / setting the baling
ram ............................................................... 233
Position of the Adhesive Safety Stickers on the
Machine ......................................................... 42
Position of the General Information Labels on the
Machine ......................................................... 44
Position of the sensors (left hand side of the
machine) ...................................................... 315
Position of the sensors (right hand side of the
machine) ...................................................... 313
Possible setting errors and their elimination
(MultiBale) .................................................... 264
Preparations for road travel ............................... 69
Pressing force control (with emergency manual
activation) ..................................................... 281
Pretension of the twine bar shaft ..................... 238
PTO operation .................................................... 38
PTO shaft ........................................................... 57
Purpose of Use .................................................. 14
R
Releasing the parking brake .............................. 71
Removing blockages........................................ 206
Re-Ordering the Adhesive Safety and Information
Labels ............................................................ 45
Replacing rollers / cam follower rollers ............ 294
Roller chute hydraulically activated ................... 70