Lenze i510 - Functions for Parameter Change-Over

11.9 Funcons for parameter change-over
The inverter supports several parameter sets. The parameter set can be selected by means of
the "Paramet
er set selecon bit 0" and "Parameter set selecon bit 1" funcons.
Details
A value set is selected in a binary-coded fashion via the triggers assigned to the two Parameter
set selecon bit 0" and " Parameter set selecon bit 1" funcons in compliance with the fol-
lowing truth table:
Parameter set selecon bit 1 Parameter set selecon bit 0 Selecon
FALSE FALSE Value set 1
FALSE TRUE Value set 2
TRUE FALSE Value set 3
TRUE TRUE Value set 4
Change-over is eected depending on the acvaon method selected in 0x4046 (PAR 755)
when a s
tate change of the selecon inputs takes place or via the trigger assigned to the
"Load parameter set" funcon.
Parameter Name / value range / [default seng] Info
0x2631:040
(PAR 400/040)
Funcon assignment: Load paramet
er set
(Funcon list: Load param.set)
•
Seng can only be changed if controller inhibit is
acve.
•
For possible sengs see descripon for
0x2631:001 (PAR 400/001). ^ 188
Assignment of a trigger for the "Load parameter set" funcon.
Trigger = FALSE-TRUE edge: parameter change-over to the value set
selected via "Parameter set selecon bit 0" and "Parameter set selecon
bit 1".
Trigger = FALSE: no acon.
Notes:
•
The acvaon method for the "Parameter change-over" funcon can
be selected in 0x4046 (PAR 755).
00 Not connected No trigger assigned (trigger is constantly FALSE).
0x2631:041
(PAR 400/041)
Funcon assignment: Parameter set selecon bit 0
(Funcon list: Par.set selecon b0)
•
Seng can only be changed if controller inhibit is
acve.
•
For possible sengs see descripon for
0x2631:001 (PAR 400/001). ^ 188
Assignment of a trigger for the "Parameter set selecon bit 0" funcon.
Selecon bit with the valency 2
0
for "Parameter change-over" funcon.
Trigger = FALSE: selecon bit = "0".
Trigger = TRUE: selecon bit = "1".
00 Not connected No trigger assigned (trigger is constantly FALSE).
0x2631:042
(PAR 400/042)
Funcon assignment: Parameter set selecon bit 1
(Funcon list: Par.set selecon b1)
•
Seng can only be changed if controller inhibit is
acve.
•
For possible sengs see descripon for
0x2631:001 (PAR 400/001). ^ 188
Assignment of a trigger for the "Parameter set selecon bit 1" funcon.
Selecon bit with the valency 2
1
for "Parameter change-over" funcon.
Trigger = FALSE: selecon bit = "0".
Trigger = TRUE: selecon bit = "1".
00 Not connected No trigger assigned (trigger is constantly FALSE).
0x4046
(PAR 755)
Acvaon of parameter set
(Param. set mode)
Selecon of the acvaon method for the parameter change-over.
0 Via command (only if the controller is
inhibited)
The parameter se
t selected via the "Parameter set selecon bit 0" and
"Parameter set selecon bit 1" funcons is acvated if the trigger
assigned in 0x2631:040 (PAR 400/040) of the "Load parameter set" func-
on supplies a FALSE-TRUE edge AND the inverter is inhibited.
1 Via command (immediately) The parameter set selected via the "Parameter set selecon bit 0" and
"Parameter set selecon bit 1" funcons is acvated if the trigger
assigned in 0x2631:040 (PAR 400/040) of the "Load parameter set" func-
on supplies a FALSE-TRUE edge.
2 If the selecon is changed (only if the
controller is inhibited)
The parameter set selected via the "Parameter set selecon bit 0" and
"Parameter set selecon bit 1" funcons is acvated if a state change of
these selecon bits takes place AND the inverter is inhibited.
3 If the selecon is changed (immediately) The parameter set selected via the "Parameter set selecon bit 0" and
"Parameter set selecon bit 1" funcons is acvated if a state change of
these selecon bits takes place.
Flexible I/O conguraon
Funcons for parameter change-over
206
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.actechdrives.com - Email: info@actechdrives.com