Lenze i510 - Analog Inputs and Outputs

Parameter Name / value range / [default seng] Info
Bit 14
Bit 15
Bit 16 Level of digital input 1 0 ≡ LOW level, 1 ≡ HIGH level.
Bit 17 Level of digital input 2
Bit 18 Level of digital input 3
Bit 19 Level of digital input 4
Bit 20 Level of digital input 5
Bit 21 Level of digital input 6
Bit 22 Level of digital input 7
Bit 23 Reserved -
Bit 24
Bit 25 Internal interconnecon of digital inputs 0 ≡ digital input terminals are set to HIGH level via pull-up resistors.
1 ≡ digital input terminals are set t
o LOW level via pull-down resistors.
Bit 26 Reserved -
Bit 27
Bit 28
Bit 29
Bit 30
Bit 31
0x4016:005 Digital output 1: Terminal state
•
Read only
Display of the logic state of output terminal X3/DO1.
0 FALSE
1 TRUE
0x4016:006 Digital output 1: Trigger signal state
•
Read only
Display of the logic state of the trigger signal for digital output 1 (without
taking a ON/OFF delay set and inversion into consideraon).
0 FALSE
1 TRUE
0x4018:005 Relay: Relay state
•
Read only
Display of the logic sta
te of the relay.
0 FALSE
1 TRUE
0x4018:006 Relay: Trigger signal state
•
Read only
Display of the logic state of the trigger signal for the relay (without tak-
ing a ON/OFF delay set and inversion into consideraon).
0 FALSE
1 TRUE
Related topics
4Conguraon of digital inputs ^ 210
4
Conguraon of digital outputs ^ 215
5.3.5.2 Analog inputs and outputs
The following parameters serve to diagnose the analog inputs and outputs of the inverter.
Parameter Name / value range / [default seng] Info
0x2DA4:001
(PAR 110/001)
Diagnoscs of analog input 1: Value in per
cent
(AI1 diagnoscs: AI1 terminal %)
•
Read only: x.x %
Display of the current input value at X3/AI1 scaled as value in percent.
•
100 % ≡ 10 V or 20 mA or 5 V
0x2DA4:002
(PAR 110/002)
Diagnoscs of analog input 1: Frequency value
(AI1 diagnoscs: AI1 scaled freq.)
•
Read only: x.x Hz
Display of the current input value at X3/AI1 scaled as a frequency value.
•
The setpoint source for speed mode is selected in 0x2860:001
(PAR 201/001).
0x2DA4:003
(PAR 110/003)
Diagnoscs of analog input 1: Process controller value
(AI1 diagnoscs: AI1 scaled PID)
•
Read only: x.xx PUnit
Display of the current input value at X3/AI1 scaled as a process controller
value.
•
The setpoint source for process controller mode is selected in
0x2860:002 (PAR 201/002).
0x2DA4:004
(PAR 110/004)
Diagnoscs of analog input 1: Torque value
(AI1 diagnoscs: AI1 scaled torque)
•
Read only: x.xx %
Display of the current input value at X3/AI1 scaled as a percentage tor-
que value.
•
100 % ≡ permissible maximum torque
Diagnoscs and fault eliminaon
Diagnoscs
Diagnoscs of the inputs and outputs
58
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.actechdrives.com - Email: info@actechdrives.com