Lenze i510 - PID Setup Group (Group 6)

Parameter Name / value range / [default seng] Info
0x29C0:002 Field controller sengs: Reset me
1.0 ... [45.5]* ... 6000.0 ms
•
Default seng depending on the size.
R
eset me Tn of the eld controller.
0x29E0:001 Field weakening controller sengs: Gain
0.000 ... [0.000]* ... 2000000.000 Vs/V
•
Default seng depending on the size.
Gain factor Vp of the eld weakening controller.
0x29E0:002 Field weakening controller sengs: Reset me
1.0 ... [1478.3]* ... 240000.0 ms
•
Default seng depending on the size.
R
eset me Tn of the eld weakening controller.
0x2B40:001 SLVC: Gain
0.0000 ... [0.2686]* ... 1000.0000 Hz/A
•
Default seng depending on the size.
Gain of the SL
VC-Q controller.
0x2B40:002 SLVC: Reset me
1.0 ... [2.3]* ... 2000.0 ms
•
Default seng depending on the size.
Reset me of the SLVC-Q controller.
0x2900:001
(PAR 332/001)
Speed controller parameters: Gain
(Speed controller: Speed contr.: gain)
0.00000 ... [0.00193]* ... 20000.00000 Nm/rpm
•
Default seng depending on the size.
Gain factor Vp of the speed controller.
0x2900:002
(PAR 332/002)
Speed controller parameters: Reset me
(Speed controller: Speed contr.: me)
1.0 ... [80.0]* ... 6000.0 ms
•
Default seng depending on the size.
Reset me Ti of the speed controller.
0x2915
(PAR 210)
Minimum frequency
(Min. frequency)
0.0 ... [0.0] ... 599.0
Hz
Lower limit value for all frequency setpoints.
0x2916
(PAR 211)
Maximum frequency
(Max. frequency)
0.0 ... [50.0] ... 599.0 Hz
Upper limit value for all frequency setpoints.
0x2942:001
(PAR 334/001)
Current controller parameters: Gain
(Current controller: I-contr.: gain)
0.00 ... [42.55]* ... 750.00 V/A
•
Default seng depending on the size.
Gain factor Vp of the current controller.
0x2942:002
(PAR 334/002)
Current controller parameters: Reset me
(Current controller: I-contr.: me)
0.01 ... [4.50]* ... 2000.00 ms
•
Default seng depending on the size.
Reset me Ti of the current controller.
0x2BA1:003
(PAR 718/003)
Flying restart circuit: Restart me
(Flying restart circuit: Flying restart me)
1 ... [5911]* ... 60000 ms
•
Default seng depending on the size.
Restart me for ying restart process.
•
The duraon of the ying restart process can be inuenced by the set-
ting of the restart me.
•
A reducon of the restart me causes an accelerated ying restart
process and therefore a reduced ying restart duraon.
0x6073
(PAR 324)
Max current
(Max current)
0.0 ... [200.0] ... 3000.0 %
Maximum overload current of the inverter.
•
100 % ≡ rated motor current 0x6075 (PAR 323)
•
If the current consumpon of the motor exceeds this current limit,
the inverter changes its dynamic behaviour, in order to counteract
this exceedance.
•
If the change in the dynamic behaviour carried out by the inverter
does not result in exing the overcurrent state, the inverter outputs
an error.
Note!
This parameter is not idencal to the so-called ulmate motor current
I
ULT
!
•
The ulmate motor current set in 0x2D46:001 (PAR 353/001) is a limit
value for synchronous motors that serves to protect their magnets.
•
The value to be set here should always be considerably below the ul-
mate motor current!
Motor control
Motor control selecon
Sensorless v
ector control (SLVC)
83
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.actechdrives.com - Email: info@actechdrives.com