Scanlab RTC 5 PC Interface Board - 10.1.5 Control Commands

RTC
®
5 PC Interface Board
Rev. 1.9 e
10 Commands And Functions
220
innovators for industry
10.1.5 Control Commands
DLL Initialization
free_rtc5_dll ........................................... 259
get_rtc_mode ......................................... 277
init_rtc5_dll ............................................. 306
set_rtc4_mode ........................................ 473
set_rtc5_mode ........................................ 473
Using Multiple RTC
®
5 Boards in One
Computer
acquire_rtc .............................................. 227
release_rtc .............................................. 392
rtc5_count_cards .................................... 396
select_rtc ................................................. 403
List Memory Commands
(n_) config_list ............................................... 243
(n_) get_config_list ........................................ 261
(n_) get_list_space ......................................... 272
(n_) load_disk ................................................. 331
(n_) save_disk ................................................. 398
Board Initialization and Field Correction
(1)
(n_) get_head_para ....................................... 265
(n_) get_sync_status ...................................... 284
(n_) get_table_para ....................................... 285
(n_) load_correction_file ............................... 328
(n_) load_program_file .................................. 340
(n_) load_stretch_table
(2)
............................ 343
(n_) load_z_table
(2)
...................................... 347
(n_) select_cor_table ...................................... 400
(n_) set_dsp_mode ........................................ 416
(n_) sync_slaves ............................................. 528
Laser Mode And Parameters
(1)
(n_) config_laser_signals ............................... 242
(n_) get_standby ............................................ 279
(n_) load_auto_laser_control ........................ 326
(n_) load_position_control ............................ 338
(n_) set_auto_laser_control ........................... 407
(n_) set_auto_laser_params .......................... 409
(n_) set_encoder_speed_ctrl ......................... 419
(n_) set_firstpulse_killer ................................ 423
(n_) set_laser_control .................................... 440
(n_) set_laser_mode ....................................... 443
(n_) set_laser_pulses_ctrl .............................. 445
(n_) set_pulse_picking ................................... 470
(n_) set_pulse_picking_length ...................... 470
(n_) set_qswitch_delay .................................. 471
(n_) set_softstart_level .................................. 484
(n_) set_softstart_mode ................................ 486
(n_) set_standby ............................................ 488
Setting The Scanner Parameters
(1)
(n_) load_varpolydelay .................................. 346
(n_) set_delay_mode ..................................... 415
(n_) set_jump_speed_ctrl .............................. 439
(n_) set_mark_speed_ctrl .............................. 448
(n_) set_sky_writing ....................................... 477
(n_) set_sky_writing_limit ............................. 478
(n_) set_sky_writing_mode ........................... 479
(n_) set_sky_writing_para ............................. 481
Coordinate Transformations
(1)
(n_) set_angle ................................................ 405
(n_) set_defocus
(2)
....................................... 414
(n_) set_matrix ............................................... 449
(n_) set_offset ................................................ 463
(n_) set_offset_xyz
(2)
................................... 464
(n_) set_scale .................................................. 474
Online Positioning
(1)
(n_) apply_mcbsp .......................................... 230
(n_) set_mcbsp_matrix .................................. 454
(n_) set_mcbsp_rot ........................................ 457
(n_) set_mcbsp_x ........................................... 458
(n_) set_mcbsp_y ........................................... 459
Status Monitoring and Diagnostics
(1)
(n_) get_head_status ..................................... 266
(n_) get_overrun ............................................ 276
(n_) get_value ................................................ 291
(n_) get_values ............................................... 293
(n_) get_waveform ........................................ 294
(n_) measurement_status .............................. 365
(n_) stop_trigger ............................................ 524
(1) Also see the corresponding list commands.
(2) Only with enabled 3D option.