SYSMEX XP Series - Connection of Power Cable

290 pages

Save Page as PDF

To Next Page

To Previous Page

5-14 Sysmex XP-300

Initial Operation

Revised March 2012

5.9 Connection of power cable

Connect the provided power cord to the power supply outlet.

Power cord

Connect to the power supply outlet

Warning!

Be sure to ground the instrument. Improper grounding may cause electrical shock.

Main Page

Table of Contents3
Introduction7
Intended Use9
Symbols Used in this Manual9
Trademarks10
Abbreviations and Units Used Throughout this Manual10
Analysis Parameters11
Safety Information13
General Information13
Installation14
Electromagnetic Compatibility (EMC)14
Avoiding Infections15
Handling of Reagents16
Maintenance17
Disposal of Waste Fluid, Waste Materials, and the Device18
Warning Labels on the Instrument21
Operators25
Design and Function27
Front View27
Right View28
Left Side Panel29
Rear Side30
Front Interior31
Left Side Interior32
Reagents33
General Information33
Cellpack33
Stromatolyser-Wh34
Cellclean35
Eightcheck-3Wp36
Symbols Used on the Labels37
Reagent Specifications38
Initial Operation39
Introduction39
Before Installation40
Preparation of Installation Location42
Removal of Packing Tape43
Connection of Reagents and Waste Bottle45
Prepare Internal Printer Paper (Printing Paper No. 3)49
Peripheral Devices (Optional)51
Connection of a Host Computer, Printer and Handheld Bar Code Reader51
Connection of Power Cable52
Basic Instrument Settings53
Operation57
Screen Display57
Menu Tree61
Signal Tones62
Pneumatic Unit Stop Function62
Timer Functions63
Emergency Stop Procedure63
SNCS Functions63
Maintenance Report64
Error Report64
File Transmission65
Emergency Call66
Sample Analysis67
Introduction67
Outline of Analysis Modes67
Flowchart of Analysis Procedure68
Checks Prior to Operation69
Switching on71
Background Check72
Quality Control72
Specimen Requirements73
Analysis in Whole Blood (WB) Mode74
Sample Preparation74
Analysis in Pre-Diluted (PD) Mode83
Display of Analysis Results93
Print and Output of Analysis Results93
End of Operation (Shutdown)94
Display and Output of Analysis Results97
Latest Sample (Analysis Result Screen)97
Stored Data107
Deleting Stored Data116
Histogram Error Flags117
Quality Control119
Control Material119
Warning and Precautions120
Manual Procedures121
Control Methods123
Quality Control Process Flow124
Control Method Selection125
Settings for Control Blood Information (QC Files)127
Performing a Quality Control134
Quality Control Chart Screen142
External Output145
Deleting Data146
Calibration147
Calibration Flow Chart148
Samples Used for Calibration149
Establishing Reference Values149
Automatic Calibration150
Manual Calibration155
Printing Calibration History158
Instrument Setup159
Introduction159
Possible Settings161
Password Setting167
Password Setting Procedure167
Print Settings169
Cleaning and Maintenance171
Maintenance Schedule171
Check Instrument Status172
Clean TD Chambers and Diluted Sample Lines (Shutdown)173
Check Trap Chamber Level and Discard175
Clean SRV Tray176
Clean TD177
Clean Waste Chamber179
Clean SRV181
Perform Auto Rinse185
Clean Rinse Cup187
Dispose Waste Fluid189
Clean Aperture of TD Chamber (Drain TD Chamber)190
Calibrate LCD Screen193
Reset SRV Cycle Counter195
Adjust Pressure and Vacuum196
Replace Reagent200
Replace System Fuses205
Replace Internal Printer Paper (Printing Paper No. 3)206
List of Consumables208
Troubleshooting209
When You Suspect an Error210
Error Messages211
Error Messages, Possible Causes and Actions to Revolve the Error215
Temperature Errors220
Memory Errors223
Maintenance Errors225
Print Error Log230
Technical Information231
Specifications231
System Limits237
Print Formats239
Connecting the Bar Code Reader242
Connection Procedure242
Hardware Specifications243
Software Specifications244
System of Units249
Functional Description251
Detection Principle251
Electric System277
Warranty278
Appendix279
Gnu General Public License281
Index287

SYSMEX XP Series - Connection of Power Cable

Table of Contents

Related product manuals