SYSMEX XP Series - Index

Sysmex XP-300 i
Index
Revised February 2013
Index
Numerics
–0.0333MPa Vacuum Error...................................... 13-7
0.05MPa Pressure Error............................................ 13-7
A
Abbreviations ............................................................. 1-4
Abbreviations and units used throughout this
manual................................................................... 1-4
Accuracy: Pre-diluted mode ..................................... 14-4
Accuracy: Whole blood mode .................................. 14-4
Action message screen ............................................... 6-3
Additional special equipment ..................................... 9-2
Adjust pressure and vacuum................................... 12-26
Adjusting pressure to 0.05 MPa ............................. 12-28
Adjusting the contrast of the LCD screen ................ 5-17
Adjusting vacuum to –0.0333 MPa ........................ 12-29
Alphabetical error message index ............................ 13-4
Analysis in pre-diluted (PD) mode........................... 7-17
Analysis in whole blood (WB) mode ......................... 7-8
Analysis modes........................................................... 7-1
Analysis of histogram............................................. 14-30
Analysis of RBC/PLT histogram............................ 14-39
Analysis of WBC histogram................................... 14-30
Analysis parameters.......................................... 1-5, 14-1
Analysis principle..................................................... 14-2
Analysis range .......................................................... 14-1
Analyzing samples.......................................... 7-15, 7-25
Aperture Clog (RBC) ............................................. 13-11
Aperture Clog (WBC) ............................................ 13-11
Appendix ................................................................ 14-49
As-needed maintenance............................................ 12-1
Automatic calibration ............................................... 10-4
Automatic settings of the TARGET value and
LIMIT value........................................................ 9-15
Automatic stop function ............................................. 6-6
Avoiding infections .................................................... 2-3
B
Background check ...................................................... 7-6
Background limits .................................................... 14-1
Bar code element dimensions................................. 14-15
Bar code label dimensions...................................... 14-16
Bar code reader settings.......................................... 14-13
Basic instrument settings.......................................... 5-15
Basic operation area ................................................... 6-2
Before installation ...................................................... 5-2
Blank Error ............................................................. 13-12
Blood cell discrimination circuit ............................ 14-29
Blood volume aspirated............................................ 14-2
C
Calculating the calibration value .............................. 10-9
Calculation of RBC constant .................................. 14-28
Calibrate LCD screen ............................................. 12-23
Calibration ................................................................ 10-1
Calibration flow chart............................................... 10-2
Carryover.................................................................. 14-5
CBC analysis .......................................................... 14-24
CELLCLEAN............................................................. 4-3
CELLPACK................................................................ 4-1
CELLPACK expired............................................... 13-10
CE-mark...................................................................... 1-2
Check digit.............................................................. 14-17
Check instrument status............................................ 12-2
Check trap chamber level and discard...................... 12-5
Checking the program version.................................. 12-2
Checks prior to operation ........................................... 7-3
Clean aperture of TD chamber
(drain TD chamber)........................................... 12-20
Clean rinse cup ....................................................... 12-17
Clean SRV .............................................................. 12-11
Clean SRV tray......................................................... 12-6
Clean TD................................................................... 12-7
Clean TD chambers and diluted sample lines
(Shutdown).......................................................... 12-3
Clean the SRV ........................................................ 13-17
Clean Transducer.................................................... 13-17
Clean Waste Chamber ............................................ 13-17
Clean waste chamber ................................................ 12-9
Cleaning and maintenance........................................ 12-1
Composition ............................................................... 9-2
Connect CELLPACK ................................................. 5-8
Connect STROMATOLYSER-WH ........................... 5-9
Connect waste line...................................................... 5-9
Connecting the bar code reader .............................. 14-12
Connection of a host computer, printer and
handheld bar code reader .................................... 5-13
Connection of power cable ....................................... 5-14
Connection of reagents and waste bottle .................... 5-7
Connection procedure............................................. 14-12
Consumable list ...................................................... 12-38
Consumption of reagent............................................ 14-2
Contact address........................................................... 1-2
Contamination Level ................................................ 14-1
Control material................................................ 9-1, 14-2
Control method selection............................................ 9-7
Control methods ......................................................... 9-5