Specifications
11 - 6
Model No.
Code No. Frequency Meter Specifications
JVOP-95S1
73041-0905X-01 TRM-45 3 V 1 mA 60/120 Hz
JVOP-95S2
73041-0905X-02 TRM-45 3 V 1 mA 90/180 Hz
JVOP-96S1
73041-0906X-01 DCF-6A 3 V 1 mA 75 Hz
JVOP-96S2
73041-0906X-02 DCF-6A 3 V 1 mA 150 Hz
JVOP-96S3
73041-0906X-03 DCF-6A 3 V 1 mA 220 Hz
The following Option Cards are available.
Table 11.4 Option Cards
Type Name Code No. Descriptions Manual No.
rds
Analog Reference Card
AI-14U
73600-C001X
Used to set high-accuracy, high-resolution analog speed refer-
ences.
S Input signal levels: 0 to +10 VDC (20 k
Ω)
1 channel
4 to 20 mA DC (250
Ω)
1 channel
S Input resolution: 14 bits (1/16384)
TOE-C736-
30.13
nce Optional C
Analog Reference Card
AI-14B
73600-C002X
Used to set high-accuracy, high-resolution analog speed refer-
ences.
S Input signal level: 0 to
±
10 VDC (20 k
Ω)
4 to 20 mA DC (500
Ω
) 3 channels
S Input resolution: 13 bits + sign (1/8192)
TOE-C736-
30.14
requency) refere
Digital Reference Card
DI-08
73600-C003X
Used to set frequency references in 2-digit BCD or 8-bit binary.
S Input signal: 8 bits binary
2 digits BCD + SIGN signal + SET signal
S Input voltage: +24 V (insulated)
S Input current: 8 mA
TOE-C736-
30.15
ector)
Speed (f
Digital Reference Card
DI-16H2
73600-C016X
Used to set 16-bit digital speed references.
S Input signal: 16 bits binary
4 digits BCD + SIGN signal + SET signal
S Input voltage: +24 V (insulated)
S Input current: 8 mA
Used to set frequency references with 16 or 12 bits (switchable).
TOE-C736-40.7
ct to conn
RS-232C/485/422 Interface
Card
SI-K2
73600-C015X
Used to convert RS-232C to RS-485 or RS-422.
Supports baud rates up to 9.6 kbps.
SPEC: F and later versions support baud rates up to 19.2 kbps.
TOE-C736-40.6
Built-in (conne
Analog Monitor Card
AO-08
73600-D001X
Converts analog signals to monitor the Inverter’s output status
(output frequency, output current, etc.) to absolute values and
outputs them.
S Output resolution: 8 bits (1/256)
S Output voltage: 0 to +10 V (not insulated)
S Output channels: 2 channels
TOE-C736-
30.21
nal Cards
Analog Monitor Card
AO-12
73600-D002X
Output analog signals to monitor the Inverter’s output status (out-
put frequency, output current, etc.).
S Output resolution: 11 bits (1/2048) + sign
S Output voltage: − 10 to +10 V (not insulated)
S Output channels: 2 channels
TOE-C736-
30.22
Monitoring Optio
Pulse Monitor Card
PO-36F
73600-D003X
Used to output pulse-train signals according to the output frequen-
cy of the Inverter
S Output pulse: 1F, 6F, 10F, 12F, 36F (F: Output frequency)
S Output voltage: +12 V
±
10% (insulated)
S Output current: 20 mA max.
TOE-C736-
30.23
Digital Output Card
DO-08
73600-D004X
Outputs isolated digital signals to monitor the Inverters operating
status (alarm signals, zero speed detection, etc.)
S Output form: Photocoupler output, 6 channels
(48 V, 50 mA max.)
Relay contact outputs, 2 channels
(
250 VAC: 1 A max., DC 30V: 1 A max.)
TOE-C736-
30.24
2C-Relay Output Card
DO-02C
73600-D007X
Provides two multi-function outputs (DPDT relay contacts) in
addition to those provided by the Inverter.
TOE-C736-40.8
11
To Next Page
Loading...
Need help?
General