17.2 Operation of Digital Operator
17.2.2 Operation of Utility Functions
17-12
Editing Program Table
The operating procedure when setting the acceleration (ACC) in program step 5 is explained
here.
Step Display after Operation Keys Operation
1
Press the key to open the Utility Function
Mode main menu, and move the cursor with the
keys to select FnB03.
2
Press the key to view the FnB03 operation
screen.
3
Move the cursor using the keys and
keys (or the + and +
keys) to select the article and program step of the
program table to be edited. Refer to the following
section for details on the methods to move the
cursor.
Method for Moving the Cursor on page 17-13
4
Press the key to move the cursor to the set-
ting side of the table.
5
Move the cursor with the keys, and
change the table settings with the keys.*
Refer to the following section for detailed setting
methods for each item.
Details on How to Set Table Settings on page
17-14
6
On pressing the key, the setting is entered
and the cursor returns to the program table article
and program step side.
7
Repeat steps 3 to 6 to set the program table. On completing the setting of all the program tables to
be used, save the program tables to flash memory by following the procedure in
Saving Program
Tables on page 17-16.
* If setting is attempted in an operation prohibited state, it will not be possible to change the setting. In this case,
make the setting again by referring to
Preparation on page 17-11.
㧮㧮ޓޓޓޓޓޓ㧙㧲㨁㧺㧯㨀㧵㧻㧺㧙
㧲㨚㧞㧜㧣ޓ㨂㧙㧹㨛㨚㨕㨠㨛㨞
㧲㨚㧮㧜㧟ޓ㧼㧳㧹ޓ㧱㨐㨕㨠
㧲㨚㧮㧜㧠ޓ㨆㧻㧺㧱ޓ㧱㨐㨕㨠
㧲㨚㧮㧜㧡ޓ㧶㧿㧼㧰ޓ㧱㨐㨕㨠
㧮㧮ޓޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧼㧻㧿㧜㧜㧜㧩㧿㨀㧻㧼
㧼㧻㧿㧜㧜㧝㧩㧿㨀㧻㧼
㧼㧻㧿㧜㧜㧞㧩㧿㨀㧻㧼
㧼㧻㧿㧜㧜㧟㧩㧿㨀㧻㧼
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧭㧯㧯㧜㧜㧞㧩㧦
㧭㧯㧯㧜㧜㧟㧩㧦
㧭㧯㧯㧜㧜㧠㧩㧦
㧭㧯㧯㧜㧜㧡㧩㧦
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧭㧯㧯㧜㧜㧞㧩㧦
㧭㧯㧯㧜㧜㧟㧩㧦
㧭㧯㧯㧜㧜㧠㧩㧦
㧭㧯㧯㧜㧜㧡㧩㧦
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧭㧯㧯㧜㧜㧞㧩㧦
㧭㧯㧯㧜㧜㧟㧩㧦
㧭㧯㧯㧜㧜㧠㧩㧦
㧭㧯㧯㧜㧜㧡㧩㧜㧜㧜㧜㧝㧜㧜㧜
㧮㧮ޓޓޓޓޓ㧙㧼㧳㧹ޓ㧱㨐㨕㨠㧙
㧭㧯㧯㧜㧜㧞㧩㧦
㧭㧯㧯㧜㧜㧟㧩㧦
㧭㧯㧯㧜㧜㧠㧩㧦
㧭㧯㧯㧜㧜㧡㧩㧜㧜㧜㧜㧝㧜㧜㧜
To Next Page
Loading...
