Alcatel-Lucent 9500 MXC

To Next Page

To Previous Page

Chapter 15. Diagnostics

Vol. IV-15-70 Alcatel-Lucent

Figure 15-27. Example Parts Screen

Main Page

Default Chapter3
- Contact Information3
- Table of Contents7
About this Manual25
- Welcome to 9500 MXC25
- Purpose25
- Intended Audience25
- What You Need to Know26
- Organization26
- Conventions and Terminology27
Chapter 1. Health and Safety31
- General Health and Safety32
- Operator Health and Safety33
- General Hazards34
- Chapter 1. 9500 MXC System Overview41
- PDH and SDH Idus57
- Ethernet IDU66
- IDU Protection84
Chapter 3. 9500 MXC Nodes95
- Platforms95
- Plug-In Cards109
- Aux160
- Npc165
- Protected Operation167
- Co-Channel Operation196
  - Xpic196
  - RAC 40 Operating Guidelines198
- Configuration and Diagnostics212
  - Configuration213
  - Diagnostics213
Chapter 4. Outdoor Units215
- ODU Construction and Mounting215
- ODU Data216
Chapter 5. Configuration and Diagnostics219
- 9500 MXC Ct219
  - 9500 MXC CT Feature Summary220
Chapter 6. 9500 MXC Performance and Diagnostic Features223
- 9500 MXC Node223
- Operation229
- Diagnostics231
Volume III 9500 MXC Installation237
- Chapter 1. Introduction239
Chapter 2. Outdoor Installations243
- Installing the Antenna243
- Installing the ODU244
- Installing a Coupler256
- Installing ODU Cables and Connectors261
- Installing Lightning Surge Suppressors265
- Weatherproofing280
  - Mastic Tape280
  - Self Amalgamating Tape281
- Chapter 3. Installing the INU and Inue283
- Chapter 4. Installing the IDU295
- Chapter 5. Antenna Alignment301
Volume IV 9500 MXC CT321
- Chapter 1. 9500 MXC CT Introduction323
- Chapter 2. Setting up 9500 MXC CT333
- Chapter 3. Installation and Configuration Process363
- Chapter 4. Licensing376
- Chapter 5. Reports385
  - Reports Screen386
    - As Built Report386
    - Helpdesk Data File387
- Chapter 6. Node and Terminal Information389
Chapter 7. Node and Terminal Plug-Ins391
- Plug-Ins Screens392
- Link Configuration393
- Dac/Tributary Configuration415
- AUX Configuration474
Chapter 8. Protection483
- Node Protection483
- Terminal Protection499
Chapter 9. Circuits509
- Circuits Configuration - Traffic510
- Circuits Configuration - Auxiliary522
  - Procedure for Configuring Auxiliary Circuits524
Chapter 10. Networking Configuration525
- Static or Dynamic Routing525
  - 9500 MXC Address and Routing Options526
    - Rules for Single and Interface Addressing Modes527
- Networking Screens528
- DHCP Server Function537
  - Rules, Hints and Tips for a DHCP Server537
  - Configuring the DHCP Server539
Chapter 11. 9500 MXC Node and Terminal Alarm Actions543
- Alarm Actions Screen543
  - Before You Begin544
  - Procedure for Alarm Actions Configuration545
Chapter 12. Date and Time Configuration547
Chapter 13. Software Management551
- Software Version Control551
- Software Management Screen552
  - Typical Loading Sequence553
    - Transfer and Activate553
  - Software Rollback555
Chapter 14. Security Configuration559
- Security Screen559
Chapter 15. Diagnostics563
- System Summary564
  - System Summary Navigation565
  - System Layout Configuration: Node568
- Event Browser569
  - Event Browser Screen Description571
  - Event Browser Navigation571
- Alarms575
  - Alarms Screen Navigation576
- History578
- Performance589
- System/Controls605
- Circuit Loopbacks for 9500 MXC Node629
- Parts631
- Advanced Management633
  - Software Reset634
  - Clear Events and History634
- Chapter 1. Commissioning639
- Chapter 2. 9500 MXC Troubleshooting658
Volume VI Appendices699
Appendix A. Ring Network Planning and Implementation701
- Ring Operation701
  - Essential Ring Nomenclature and Rules702
- Planning a Ring Network704
- Installing a Ring Network707
- Configuring a Ring Network708
- Commissioning and Troubleshooting a Ring Network721
Appendix B. 9500 MXC Alarms727
- NCC/IDU Alarms728
- AUX Alarms766
- Informational Events784
Appendix C. Inu/Inue and IDU Connector and Cable Data793

Alcatel-Lucent 9500 MXC - Page 632

Table of Contents

Related product manuals