Fuji Electric FRENIC-Ace series - Page 56

2.2 Wiring
2-24
Table 2.2-14 Recommended Wire Sizes, Ambient temperature: Below 40°C, Wire type: 75°C wire (continued)
HND Mode, Ambient temperature: Below 40°C, Wire type: 75°C wire
Power
System
Std
Applicable
Motor
(kW)
Inverter type
Recommended wire size (mm
2
)
Main power supply input
[L1/R, L2/S, L3/T]
Ground
terminal
[
z
G]
Inverter
output
[U, V, W]
For DC
reactor
connection
[P1, P(+)]
For braking
resistor
connection
[P(+), DB]
With DC
reactor
Without DC
reactor
Three-phase 200 V
0.2
FRN0001E2■-2

2
2
2
2
2
2
0.4
FRN0002E2■-2
2
2
2
2
2
2
0.75
FRN0004E2■-2

2
2
2
2
2
2
1.5
FRN0006E2■-2
2
2
2
2
2
2
2.2
FRN0010E2■-2

2
2
2
2
2
2
3.0
FRN0012E2■-2
*10
2
2
2
2
2
2
5.5
FRN0020E2■-2

*10
2
3.5
3.5
2
2
2
7.5
FRN0030E2■-2
2
5.5
5.5
3.5
3.5
2
11
FRN0040E2■-2

5.5
8
5.5
5.5
5.5
2
15
FRN0056E2■-2
8
14
5.5
8
14
2
18.5
FRN0069E2■-2

14
22
8
14
14
2
22
FRN0088E2■-2
14
22
8
14
22
2
30
FRN0115E2■-2

22
38
*7
14
22
38
*7
2
Three-phase 400 V
0.75
FRN0002E2■-4

2
2
2
2
2
2
1.1
FRN0004E2■-4
2
2
2
2
2
2
2.2
FRN0006E2■-4

2
2
2
2
2
2
3.0
FRN0007E2■-4
*10
2
2
2
2
2
2
5.5
FRN0012E2■-4

*10
2
2
2
2
2
2
7.5
FRN0022E2■-4
2
2
2
2
2
2
11
FRN0029E2■-4

2
3.5
3.5
2
2
2
15
FRN0037E2■-4
2
5.5
3.5
3.5
3.5
2
18.5
FRN0044E2■-4

5.5
8
5.5
5.5
5.5
2
22
FRN0059E2■-4
5.5
8
*1
5.5
5.5
5.5
2
30
FRN0072E2■-4

8
*1
14
8
*1
8
*1
14
2
37
FRN0085E2■-4
14
14
8
14
14
-
45
FRN0105E2■-4

14
22
8
14
22
-
55
FRN0139E2■-4
22
38
14
22
38
-
75
FRN0168E2■-4

38
-
14
38
38
-
90
FRN0203E2■-4
38
-
14
60
60
-
110
FRN0240E2■-4

60
-
22
60
100
-
132
FRN0290E2■-4
100
-
22
100
100
-
160
FRN0361E2■-4

100
-
22
100
150
-
200
FRN0415E2■-4
150
-
38
150
200
-
220
FRN0520E2■-4

150
-
38
150
200
-
280
FRN0590E2■-4
200
-
38
250
325
-
The recommended wire sizes for the main circuit terminals assume using 75°C 600V HIV wire.
*1 For compatible crimped terminals, please use model 8-L6 by JST Mfg. Co., Ltd. or equivalent.
*4 For compatible crimped terminals, please use model R5.5-6 by JST Mfg. Co., Ltd. or equivalent.
*7 For compatible crimped terminals, please use model 38-6 by JST Mfg. Co., Ltd. or equivalent.
*10 ND-spec.