FUTABA T12K

107
<Functions of Linkage Menu>
●Selectthefunctionname
andreturntotheLinkage
menubypushingthe RTN
buttonor pushingthe
HOME/EXITbutton.
<Push Dial>
RETURN
TELEMETRY : RPM
DisplayingdatafromtheRPM
RPM is a screen which displays / sets up the
RPM information from an optional RPM sensor.
The RPM of the model (engine, motor, etc.)
which is ying can be shown.
If it becomes higher or lower than the setting an
alarm and/or vibration will alert you.
*It cannot be used in S-FHSS mode.
●Select[RPM]intheTELEMETRYscreen
andaccessthesetupscreenshown
belowbypushingtheRTNbutton.
●Pushthe S1buttontoadvancetothenextpage.
●RPM
●Themaximumandtheminimumwhen
poweringONareshown.
●Selectthesensoryouuse.
SBS-01RM:MAGNETIC
SBS-01RO:OPTICAL
SBS-01RB:BLSMOTOR
●↓Adownwardarrow
indicatesthatthe
alarmwillsound
whentheRPMfalls
belowthesetvalue.
●↑Anupwardarrow
indicatesthatthe
alarmwillsound
whentheRPMrises
abovethesetvalue.
Alert set : Over rotations
1.Movethecursortothe↑ALERTitemandpush
theRTNbuttontoswitchtothedatainput
mode.
2.SelecttheACTmodebyscrollingthePush
dial.
3.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
4.Movethecursortothe↑THRESHOLD[2000
rpm]itemandpushtheRTNbuttontoswitch
tothedatainputmode.
5.AdjusttheratebyscrollingthePushdial.
 Initialvalue:2000rpm
 Adjustmentrange:1rpm~150,000rpm
(↑THRESHOLD>↓THRESHOLD)
*When the RTN button is pushed for one second, the rate is
reset to the initial value.
6.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
Alert set : Under rotations
1.ScrolltothesecondpagebypushingS1.
Movethecursortothe↓ALERTitemandpush
theRTNbuttontoswitchtothedatainput
mode.
2.SelecttheACTmodebyscrollingthePush
dial.
3.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
4.Movethecursortothe↓THRESHOLD[0rpm]
itemandpushtheRTNbuttontoswitchto
thedatainputmode.
5.AdjusttheratebyscrollingthePushdial.
 Initialvalue:0rpm
 Adjustmentrange:0rpm~149,999rpm
(↑THRESHOLD>↓THRESHOLD)
*When the RTN button is pushed for one second, the rate is
reset to the initial value.
6.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
TYPE 1
TYPE 2
TYPE 3
TYPE 4
"Vibes" type
Ifthefollowingtypesareselected,the
transmitterwillvibrateduringthewarning.
●In"MAGNETIC",thegearratioofyour
engine(motor)youareusingisentered.
●In"BLSMOTOR",thenumberofpolesyour
brushless motoryouareusingisentered.
●In"OPTICAL",thenumber
ofbladesofthepropeller
(rotor)yourmodelis
entered.
*A RPM sensor must be installed in the aircraft.
Scrolling
●Movingcursor
●Selectingmode
●Adjustingvalue
●Tonextpage
●Toinputdatamode
●Dataisentered