FUTABA T12K - Telemetry:current Sensor

119
<Functions of Linkage Menu>
●Selectthefunctionname
andreturntotheLinkage
menubypushingthe RTN
buttonor pushingthe
HOME/EXITbutton.
<Push Dial>
RETURN
TELEMETRY : Current sensor
Displayingdatafromthedrivebatterycurrent
The SBS-01C has the capability of measuring
current, voltage and capacity (consumption) from
drive battery all at the same time.
*It cannot be used in S-FHSS mode
●Select[CURRENT]intheTELEMETRYscreenandaccessthe
setupscreenshownbelowbypushingtheRTNbutton.
●Displaysthecurrentdata
●Displaysthemaximum/minimumdata
afterthetransmitteristurnedon.
●Currentalarmsettingrange
-150A
～
150A
(↑THRESHOLD>↓THRESHOLD)
*Alarm when the current has increased.
●Currentalarmsettingrange-150A
～
150A
(↑THRESHOLD>↓THRESHOLD)
*Alarm when the current has decreased.
Alert setting when current increases
1.Set“↑ALERT”onthe<CURRENT>screento
ACT.MovethecursortoINHandpushtheRTN
button.
2.SelecttheACTmodebyscrollingthePushdial.
3.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
4.Thecurrentatwhichanalarmisgenerated
canbesetbyselectingthecurrentdisplaynext
to“↑THRESHOLD”andpushingtheRTNbutton.
Thisgeneratesanalarmwhenthecurrent
increases.
5.AdjusttheratebyscrollingthePushdial.
*When the RTN button is pushed for one second, the rate is
reset to the initial value.
6.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
Alert setting when current decreases
1.Selectpage2bypushingS1fromthe
<CURRENT>screenandset“↓ALERT”toACT.
2.SelecttheACTmodebyscrollingthePush
dial.
3.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
4.Thecurrentatwhichanalarmisgenerated
canbesetbyselectingthenumericaldisplay
nextto“↓THRESHOLD”andpushingtheRTN
button.Thissoundsanalarmwhenthecurrent
decreases.
5.AdjusttheratebyscrollingthePushdial.
*When the RTN button is pushed for one second, the rate is
reset to the initial value.
6.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
*SBS-01C must be installed in the aircraft.
TYPE 1
TYPE 2
TYPE 3
TYPE 4
"Vibes" type
Ifthefollowingtypesareselected,the
transmitterwillvibrateduringthewarning.
●PushtheS1buttontoadvancetothenextpage.
[Current]
Drive
Battery
SBS-01C
to Receiver
Motor
ESC
●↓Adownwardarrow
indicatesthealarm
willsoundwhenthe
currentreachesbelow
yoursetvalue.
●↑Anupwardarrow
indicatesthealarm
willsoundwhenthe
currentreaches
aboveyoursetvalue.
Scrolling
●Movingcursor
●Selectingmode
●Adjustingvalue
●Tonextpage
●Toinputdatamode
●Dataisentered