FUTABA T12K

113
<Functions of Linkage Menu>
●Selectthefunctionname
andreturntotheLinkage
menubypushingthe RTN
buttonor pushingthe
HOME/EXITbutton.
<Push Dial>
RETURN
TELEMETRY : DISTANCE
DisplayingdatafromtheDistanceScreen
The Distance screen displays and sets altitude
data from an SBS-01G/02G GPS Sensor (sold
separately), and allows the distance to the airborne
aircraft to be read by the transmitter. When the
aircraft flies inside or outside the set distance an
alarm and vibration alerts the pilot.
*The GPS sensor is necessary, and is sold separately. Mount
and connect the sensor in accordance with the sensor
instruction manual.
*It cannot be used in S-FHSS mode
●Select[DISTANCE]intheTELEMETRYscreenandaccess
thesetupscreenshownbelowbypushingtheRTN
button.
●Currentdistance
●Distancealarmsetting
range1m
～
5,000m
*Alarm when the aircraft moves far
away.
(↑THRESHOLD>↓THRESHOLD)
●Distancealarmsettingrange0m
～
4,999m
(↑THRESHOLD>↓THRESHOLD)
●ThisindicatesMaximum
Distancetheaircraftewto.
●The↓arrowshows
thatanalarmis
generatedwhen
thedistancedrops
belowthesetvalue.
●The↑arrowshows
thatanalarmis
generatedwhen
thesetvalueis
exceeded.
Setting the reference position
1.Turnonthetransmitterandthemodelwith
theGPSsensorinstalledinit.
2.WaitfortheGPSaccuracyindicatorto
displaythreebars.
3.MovethecursortoREFERENCE[SET]andpush
theRTNbutton.Themodel'scurrentposition
isnowstoredandthedistanceissetto0yd.
4.PushtheRTNbutton.(Toterminatetheinputand
returntotheoriginalstate,pushtheS1button.)
*Now, the position of the present model was set to 0 m.
Setting a "too far" alert distance
1.Movethecursortothe↑ALERTitemandpush
theRTNbuttontoswitchtothedatainput
mode.
2.SelecttheACTmodebyscrollingthePush
dial.
3.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
4.Movethecursortothe↓THRESHOLD[1,000m]
itemandpushtheRTNbuttontoswitchto
thedatainputmode.
5.AdjustthedistancebyscrollingthePushdial.
*When the RTN button is pushed for one second, the rate is
reset to the initial value.
6.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
TYPE 1
TYPE 2
TYPE 3
TYPE 4
"Vibes" type
*A GPS sensor must be installed in the aircraft.
Ifthefollowingtypesareselected,the
transmitterwillvibrateduringthewarning.
●Pushthe S1buttontoadvancetothenextpage.
●ThisindicatesthereceivingaccuracyfromaGPSsatellite.When
threebarsaredisplayed,theGPSisreadyforuse.Pushing
[REFERENCE]setsthecurrentaircraftpositionasthestartingpoint.
*Positioning time of GPS
A short time is required until the positioning of
the GPS is established. In the meantime, don't
move the model during this process. Wait until
the GPS sensor's LED turns solid green. If it is
blinking green it is still acquiring the satellite
signals.
Scrolling
●Movingcursor
●Selectingmode
●Adjustingvalue
●Tonextpage
●Toinputdatamode
●Dataisentered