FUTABA T12K

116
<Functions of Linkage Menu>
●Selectthefunctionname
andreturntotheLinkage
menubypushingthe RTN
buttonor pushingthe
HOME/EXITbutton.
<Push Dial>
RETURN
TELEMETRY : Servo sensor
DisplayingdatafromtheS.BUSservo
The SBS-01S can monitor and display the
in-flight current, operating angle, and internal
temperature of up to two S.BUS2 servos.
If you forget to connect the servo wiring during
fuselage assembly, or the servo was disconnected,
an alarm can be activated at the transmitter.
*It cannot be used in S-FHSS mode
●Select[CURR.#1]intheTELEMETRYscreenandaccessthe
setupscreenshownbelowbypushingtheRTNbutton.
●Displaysthecurrentdata
●Displaysthemaximum/minimumdata
afterthetransmitteristurnedon.
●Currentalarmsettingrange
0.1
～
10A
(↑THRESHOLD>↓THRESHOLD)
*Alarm when the current has increased.
●Currentalarmsettingrange0
～
9.9A
(↑THRESHOLD>↓THRESHOLD)
*Alarm when the current has decreased.
Alert setting when servo #1 current increases
1.Set“↑ALERT”onthe<CURR.#1>screento
ACT.MovethecursortoINHandpushtheRTN
button.
2.SelecttheACTmodebyscrollingthePushdial.
3.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
4.Thecurrentatwhichanalarmisgenerated
canbesetbyselectingthecurrentdisplaynext
to“↑THRESHOLD”andpushingtheRTNbutton.
Thisgeneratesanalarmwhenthecurrent
increases.
5.AdjusttheratebyscrollingthePushdial.
*When the RTN button is pushed for one second, the rate is
reset to the initial value.
6.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
Alert setting when servo #1 current decreases
1.Selectpage2bypushingS1fromthe
<CURR.#1>screenandset“↓ALERT”toACT.
2.SelecttheACTmodebyscrollingthePush
dial.
3.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
4.Thecurrentatwhichanalarmisgenerated
canbesetbyselectingthenumericaldisplay
nextto“↓THRESHOLD”andpushingtheRTN
button.Thissoundsanalarmwhenthecurrent
decreases.
5.AdjusttheratebyscrollingthePushdial.
*When the RTN button is pushed for one second, the rate is
reset to the initial value.
6.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
*SBS-01S must be installed in the aircraft.
TYPE 1
TYPE 2
TYPE 3
TYPE 4
"Vibes" type
Ifthefollowingtypesareselected,the
transmitterwillvibrateduringthewarning.
●PushtheS1buttontoadvancetothenextpage.
[Current]
SBS-01S
TO Receiver
S.BUS2 Port
S.BUS2 servo
Whenit'sservo2,select#2.
Servo#1
Servo#2
●↓Adownwardarrow
indicatesthealarm
willsoundwhenthe
currentreachesbelow
yoursetvalue.
●↑Anupwardarrow
indicatesthealarm
willsoundwhenthe
currentreaches
aboveyoursetvalue.
Scrolling
●Movingcursor
●Selectingmode
●Adjustingvalue
●Tonextpage
●Toinputdatamode
●Dataisentered