FUTABA T12K

108
<Functions of Linkage Menu>
●Selectthefunctionname
andreturntotheLinkage
menubypushingthe RTN
buttonor pushingthe
HOME/EXITbutton.
<Push Dial>
RETURN
TELEMETRY : ALTITUDE
Displayingdatafromthealtitude
ALTITUDE is a screen which displays / sets up the
altitude information from an optional altitude sensor or
GPS sensor. The altitude of the model which is flying
can be known. You can set an alarm to sound when the
model flies above your preset maximum altitude. You
can also choose to receive your warning as a vibration.
The initial altitude data that appears when your power
supply is turned on will be zero meters. From there, it
displays your altitude as it changes. Even if the altitude
of an aireld is high, that shall be 0 m and the altitude
difference from an airfield is displayed. This sensor
calculates the altitude from atmospheric pressure.
Atmospheric pressure will get lower as you go up in
altitude. Using this the sensor will estimate the altitude.
Please understand that an exact advanced display cannot
be performed if atmospheric pressure changes in a
weather situation.
*It cannot be used in S-FHSS mode
●Select[ALTITUDE]intheTELEMETRYscreenandaccessthe
setupscreenshownbelowbypushingtheRTNbutton.
●Altitude
●Themaximumandtheminimumwhen
poweringONareshown.
●↓Adownwardarrow
indicatesthealarm
willsoundwhenthe
altitudereachesbelow
yoursetvalue.
●↑Anupwardarrow
indicatesthealarm
willsoundwhenthe
altitudereaches
aboveyoursetvalue.
First, you need to set a reference point.
1.Themodelandtransmittertowhichthe
altitudesensorwasconnectedareturnedon.
2.Movethecursortothe[SET]of"REFERENCE"
itemandpushtheRTNbuttontoswitchto
thedatainputmode.
3.PushtheRTNbutton.(Toterminatetheinputand
returntotheoriginalstate,pushtheS1button.)
*Atmospheric pressure is changed according to the weather
also at the same aireld. You should preset before a ight.
Alert set : High side
1.Movethecursortothe↑ALERTitemandpush
theRTNbuttontoswitchtothedatainput
mode.
2.SelecttheACTmodebyscrollingthePush
dial.
3.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
4.Movethecursortothe↑THRESHOLD[+200m]
itemandpushtheRTNbuttontoswitchto
thedatainputmode.
5.AdjusttheratebyscrollingthePushdial.
 Initialvalue:+200m
 Adjustmentrange:-499m~+5,000m
(↑THRESHOLD>↓THRESHOLD)
*When the RTN button is pushed for one second, the rate is
reset to the initial value.
6.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
Alert set : Low side
1.ScrolltothesecondpagebypushingS1.Move
thecursortothe↓ALERTitemandpushtheRTN
buttontoswitchtothedatainputmode.
2.SelecttheACTmodebyscrollingthePush
dial.
3.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
4.Movethecursortothe↓THRESHOLD[-50m]
itemandpushtheRTNbuttontoswitchto
thedatainputmode.
5.AdjusttheratebyscrollingthePushdial.
 Initialvalue:-50m
 Adjustmentrange:-500m~+4,999m
(↑THRESHOLD>↓THRESHOLD)
*When the RTN button is pushed for one second, the rate is
reset to the initial value.
6. PushtheRTNbutton.(Toterminatetheinputand
returntotheoriginalstate,pushtheS1button.)
TYPE 1
TYPE 2
TYPE 3
TYPE 4
"Vibes" type
Ifthefollowingtypesareselected,the
transmitterwillvibrateduringthewarning.
*An altitude sensor or GPS sensor must be installed in the aircraft.
●PushtheS1buttontoadvancetothenextpage.
Scrolling
●Movingcursor
●Selectingmode
●Adjustingvalue
●Tonextpage
●Toinputdatamode
●Dataisentered