FUTABA T12K

94
<Functions of Linkage Menu>
●Selectthefunctionname
andreturntotheLinkage
menubypushingthe RTN
buttonor pushingthe
HOME/EXITbutton.
<Push Dial>
RETURN
T1-T4 SET.
Digitaltrimsettings
This function adjusts the digital trim's step
amount and operation mode (T1~T4.)
When the flight conditions are set, the trim
operation can be coupled with the conditions when
combination mode is selected.
The T12K unit of trim is displayed on the home
screen.
Control step amount setting
1.Movethecursortothe[STEP]itemandpush
theRTNbuttontoswitchtothedatainput
mode.
2.Setthecontrolstepamountbyscrollingthe
Pushdial.
 Initialvalue:4
 Adjustmentrange:0~200
*When the RTN button is pushed for one second, the control
step amount is reset to the initial value.
*When the value is increased, the change per step becomes
larger.
3.PushtheRTNbuttontoendadjustmentand
returntothecursormode.
Separate/combination mode selection (Heli and
Glider only)
1.Movethecursortothe[MODE]itemand
pushtheRTNbuttontoswitchtothedata
inputmode.
2.SelectthemodebyscrollingthePushdial.A
conrmationmessageappears.
*The display blinks.
 [COMB.]:Combinationmode.Thetrim'sdata
isreectedinallightconditions.
 [SEPAR]:Separatemode.Trimadjustments
aremadeindividuallyforeachflight
condition.
3.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
Display unit selection
1.Movethecursortothe[UNIT]itemandpush
theRTNbuttontoswitchtothedatainput
mode.
2.SelectthemodebyscrollingthePushdial.A
conrmationmessageappears.
*The display blinks.
 [--]:Astepnumberisdisplayedonthehome
screen.Thereisnounitdisplay.
 [%]:"%"isdisplayedasaunit.
3.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
Trim Memory Operation procedure
1.Movethecursortothe[T1-T4MEMORY]item
andpushtheRTNbuttontoswitchtothe
datainputmode.
2.SelecttheACTmodebyscrollingthePush
dial.Aconrmationmessageappears.
 [INH]:Inhibited
 [ACT]:Activated
3.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
4.Atthehomescreen,movethecursortothe
trimyouwanttochangeandpushtheRTN
foronesecond.Thetrimdisplayismovedto
thecenterposition.
*When the function is inhibited, the trim position returns to
the actual trim position.
Only the trim displayed on the home screen can
be moved to the center position without changing
the actual trim's memory position.
●Select[T1-T4SET.]intheLinkagemenuandaccess
thesetupscreenshownbelowbypushingtheRTN
button.
(The display screen is an example. The
screen depends on the model type.)
●Trimoperationmode
"COMB.":Combinationmode
"SEPAR":Separatemode
*The display blinks.
Scrolling
●Movingcursor
●Selectingmode
●Adjustingvalue
●Toinputdatamode
●Dataisentered