FUTABA T12K

117
<Functions of Linkage Menu>
●Selectthefunctionname
andreturntotheLinkage
menubypushingthe RTN
buttonor pushingthe
HOME/EXITbutton.
<Push Dial>
RETURN
TELEMETRY : Servo sensor
DisplayingdatafromtheS.BUSservo
The SBS-01S can monitor and display the in-
flight internal temperature of up to two S.BUS2
servos.
*It cannot be used in S-FHSS mode
●Select[TEMP.#1]intheTELEMETRYscreenandaccessthe
setupscreenshownbelowbypushingtheRTNbutton.
●Displaysthecurrentdata
●Displaysthemaximum/minimumdata
afterthetransmitteristurnedon.
●Tempalarmsettingrange
-9
～
115
℃
(↑THRESHOLD>↓THRESHOLD)
*Alarm when the temp has increased.
●Tempalarmsettingrange-10
～
114
℃
(↑THRESHOLD>↓THRESHOLD)
*Alarm when the temp has decreased.
Alert setting when servo #1 temperature increases
1.Set“↑ALERT”onthe<TEMP.#1>screentoACT.
MovethecursortoINHandpushtheRTN
button.
2.SelecttheACTmodebyscrollingthePushdial.
3.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
4.Thetemperatureatwhichanalarmis
generatedcanbesetbyselectingthe
temperaturedisplaynextto“↑THRESHOLD”
andpushingtheRTNbutton.Thisgeneratesan
alarmwhenthetemperatureincreases.
5.AdjusttheratebyscrollingthePushdial.
*When the RTN button is pushed for one second, the rate is
reset to the initial value.
6.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
Alert setting when servo #1 temperature decreases
1.Selectpage2bypushingS1fromthe
<TEMP.#1>screenandset“↓ALERT”toACT.
2.SelecttheACTmodebyscrollingthePush
dial.
3.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
4.Thetemperatureatwhichanalarmis
generatedcanbesetbyselectingthe
numericaldisplaynextto“↓THRESHOLD”
andpushingtheRTNbutton.Thissoundsan
alarmwhenthetemperaturedecreases.
5.AdjusttheratebyscrollingthePushdial.
*When the RTN button is pushed for one second, the rate is
reset to the initial value.
6.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
*SBS-01S must be installed in the aircraft.
TYPE 1
TYPE 2
TYPE 3
TYPE 4
"Vibes" type
Ifthefollowingtypesareselected,the
transmitterwillvibrateduringthewarning.
●PushtheS1buttontoadvancetothenextpage.
[Temperature]
SBS-01S
TO Receiver
S.BUS2 Port
S.BUS2 servo
Whenit'sservo2,select#2.
Servo#1
Servo#2
●↓Adownwardarrow
indicatesthealarm
willsoundwhenthe
temperaturereaches
belowyoursetvalue.
●↑Anupwardarrow
indicatesthealarm
willsoundwhenthe
temperaturereaches
aboveyoursetvalue.
Scrolling
●Movingcursor
●Selectingmode
●Adjustingvalue
●Tonextpage
●Toinputdatamode
●Dataisentered