FUTABA T12K

118
<Functions of Linkage Menu>
●Selectthefunctionname
andreturntotheLinkage
menubypushingthe RTN
buttonor pushingthe
HOME/EXITbutton.
<Push Dial>
RETURN
TELEMETRY : Servo sensor
DisplayingdatafromtheS.BUSservo
The SBS-01S can monitor and display the in-
ight angle and internal temperature of up to two
S.BUS2 servos.
If you forget to connect the servo wiring during
fuselage assembly, or the servo was disconnected,
an alarm can be activated at the transmitter.
*It cannot be used in S-FHSS mode
●Select[ANGLE#1]intheTELEMETRYscreenandaccessthe
setupscreenshownbelowbypushingtheRTNbutton.
●Displaystheangledata
●Displaysthemaximum/minimumdata
afterthetransmitteristurnedon.
●Anglealarmsettingrange
-179.9
～
+180
°
(↑THRESHOLD>↓THRESHOLD)
*Alarm when the angle has increased.
●Anglealarmsettingrange-180
～
+179.9
°
(↑THRESHOLD>↓THRESHOLD)
Alert setting when servo #1 angle increases
1.Set“↑ALERT”onthe<ANGLE#1>screento
ACT.MovethecursortoINHandpushtheRTN
button.
2.SelecttheACTmodebyscrollingthePushdial.
3.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
4.Theangleatwhichanalarmisgeneratedcan
besetbyselectingtheangledisplaynextto“↑
THRESHOLD”andpushingtheRTNbutton.This
generatesanalarmwhentheangleincreases.
5.AdjusttheratebyscrollingthePushdial.
*When the RTN button is pushed for one second, the rate is
reset to the initial value.
6.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
1.Set“CONNECTION”onthe<ANGLE>screento
ACT.MovethecursortoINHandpushtheRTN
button.
2.SelecttheACTmodebyscrollingthePushdial.
3.PushtheRTNbutton.
Alert setting when servo #1 angle decreases
1.Selectpage2bypushingS1fromthe
<ANGLE#1>screenandset“↓ALERT”toACT.
2.SelecttheACTmodebyscrollingthePush
dial.
3.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
4.Theangleatwhichanalarmisgenerated
canbesetbyselectingthenumericaldisplay
nextto“↓THRESHOLD”andpushingtheRTN
button.Thissoundsanalarmwhentheangle
decreases.
5.AdjusttheratebyscrollingthePushdial.
*When the RTN button is pushed for one second, the rate is
reset to the initial value.
6.PushtheRTNbutton.(Toterminatetheinput
andreturntotheoriginalstate,pushtheS1
button.)
*SBS-01S must be installed in the aircraft.
TYPE 1
TYPE 2
TYPE 3
TYPE 4
"Vibes" type
Ifthefollowingtypesareselected,the
transmitterwillvibrateduringthewarning.
●PushtheS1buttontoadvancetothenextpage.
[Angle]
Whenit'sservo2,select#2.
Connect Alarm setting
*This alarm and display is limited to the S.BUS
servos connected to the servo sensors.
If you forget to connect the servo wiring during
fuselage assembly, or the servo was disconnected,
an alarm can be activated at the transmitter.
*Alarm when the angle has decreased.
●↓Adownwardarrow
indicatesthealarm
willsoundwhenthe
anglereachesbelow
yoursetvalue.
●↑Anupwardarrow
indicatesthealarm
willsoundwhenthe
anglereachesabove
yoursetvalue.
Scrolling
●Movingcursor
●Selectingmode
●Adjustingvalue
●Tonextpage
●Toinputdatamode
●Dataisentered