FUTABA T12K

132
<Model Menu (Common Functions)>
●ON/OFF switch setting
 Movethecursortotheswitchitemand
accesstheswitchsetupscreenbypushing
theRTNbuttonandselecttheswitchandON
direction.
*For a detailed description of the setting method, see [Switch
Setting Method] at the back of this manual.
*Always on when [--].
●Master channel setting
1.Movethecursortothe[MASTER]itemand
pushtheRTNbuttontoswitchtothedata
inputmode.
 SelectthefunctionbyscrollingthePushdial.
*The display blinks.
 PushtheRTNbuttontochangethefunction
andreturntothecursormode.
2.Whenyouwanttolinkthismixingwithother
mixes,movethecursortothe[LINK]itemand
pushtheRTNbuttontoswitchtothedata
inputmode.
 Selectthelinkmode,either[+]or[-],by
scrollingthePushdial.
*The display blinks.
 PushtheRTNbuttontosetthelinkmodeand
returntothecursormode.
*Check to ensure that the link mode is functioning properly
by operating the mix accordingly.
*Master channel control can be set to activate based on
the amount of stick input, or VR input, neither of which
includes ATV, D/R, and mixing selection. In this case, the
switch setup screen is displayed by pushing the RTN button
with "H/W" selected in the function selection. Select master
channel control. (To terminate the "H/W" selection, select
the [--] display and push the RTN button.
●Slave channel setting
1.Movethecursortothe[SLAVE]itemand
pushtheRTNbuttontoswitchtothedata
inputmode.
 SelectthefunctionbyscrollingthePushdial.
*The display blinks.
 PushtheRTNbuttontochangethefunction
andreturntothecursormode.
2.Whenyouwanttolinkthismixingwithother
mixes,movethecursortothe[LINK]itemand
pushtheRTNbuttontoswitchtothedata
inputmode.
 Selectthelinkmodeto[+]or[-]byscrolling
thePushdial.
*The display blinks.
 PushtheRTNbuttontosetthelinkmodeand
returntothecursormode.
*Check the direction by actual operation.
●Trim mode ON/OFF setting
1.Whenchangingthetrimmode,movethe
cursortothe[TRIM]itemandpushtheRTN
buttontoswitchtothedatainputmode.
 SelectON/OFFbyscrollingthePushdial.
*The display blinks.
 PushtheRTNbuttontochangethetrim
modeON/OFFandreturntothecursor
mode.
*To incorporate the mixing from the master trim, select [ON].
If trim is not desired, select [OFF].
*Effective when a function is set in the master channel.
●Linear curve setting
[Ratesetting]
1.Movethecursortothemixingratesetting
itemandpushtheRTNbuttontoswitchto
thedatainputmode.
 AdjusttheratebyscrollingthePushdial.
 Initialvalue:0%
 Adjustmentrange:-100%~+100%
*When the RTN button is pushed for one second, the servo
operation position is reset to the initial value.
 PushtheRTNbuttontoendadjustmentand
returntothecursormode.
2.Repeatthisprocedureforallotherratesas
desired.
[Offsettingthecurvehorizontallyinthevertical
orhorizontaldirection]
1.Movethecursortothe[OFFS]settingitem
andpushtheRTNbuttontoswitchtothe
datainputmode.
 AdjusttheoffsetratebyscrollingthePush
dial.
 Initialvalue:0%
 Adjustmentrange:-100%~+100%
*When the RTN button is pushed for one second, the servo
operation position is reset to the initial value.)
 PushtheRTNbuttontoendtheadjustment
andreturntothecursormode.
2.Repeatthisprocedurefortheotherdirection.
●5-point curve setting
[Ratesetting]
1.Movethecursortothepointratesettingitem
youwanttoadjustandpushtheRTNbutton
toswitchtothedatainputmode.
 AdjusttheratebyscrollingthePushdial.
 Initialvalue:0%
 Adjustmentrange:-100%~+100%
*When the RTN button is pushed for one second, the servo
operation position is reset to the initial value.)
 PushtheRTNbuttontoendtheadjustment
andreturntothecursormode.
2.Repeatthisprocedureforeachpointas
desired.