FUTABA T12K - Page 188

188
<Appendix>
Timer setting
●Up timer/down timer setting
 Movethecursortothe[MODE]itemand
pushtheRTNbuttontoswitchtothedata
inputmode.
 SelectthemodebyscrollingthePushdial
andpushtheRTNbutton.
 [UP]:Uptimer
 [DOWN]:Downtimer
 [HOUR]:Hourmodetimer
●Timer time setting
 Movethecursortothe[ALARM]itemand
pushtheRTNbuttontoswitchtothedata
inputmode.
 SetthetimebyscrollingthePushdial.
 [00]:[00]:[min]:[sec]
 PushtheRTNbuttontoendtheadjustment
andreturntothecursormode.
●Switch setting
 Movethecursortotheitemoftheswitchyou
wanttoset,accesstheswitchsetupscreen
bypushingtheRTNbutton.Selecttheswitch
andONdirection.
[For a detailed description of the setting method, see [Switch
Setting Method] located on the next page.]
 [START]:Startswitch
 [STOP]:Stopswitch
 [RESET]:Resetswitch
●Memory setting
 Movethecursortothe[MEMORY]itemand
pushtheRTNbuttontoswitchtothedata
inputmode.
 SelectthemodebyscrollingthePushdial
andpushtheRTNbutton.
 [OFF]:MemoryfunctionOFF
 [ON]:Modewherethetimerisnotresetwhen
turnedpoweroffandswitchedthemodel.
●A mode which sounds an alarm each minute
can be selected.
 Changethesettingusingthe"

"button(or
"

"button).
"

":Alarmsoundseachminuteofthetime
elapsedfromtimerstart.(Conventional
mode)
"

":Alarmsoundseachminuteofthetime
remaininguptothealarmtime.
Timer operation
● TimerST1andST2arestarted/stoppedbya
pre-selectedstart/stopswitch.
● Toresetatimer,operatethepre-selected
resetswitch,ormovethecursortothe[RESET]
displayonthetimerscreenandpushtheRTN
button.
Speech function
Speechfunctionisadded
toTIMER(ST1andST2).
WhentheUporDowntimersare
activated,speechoutputisavailable.
Itisphoneoutputonly.
■↑ mode
Thevoiceoutputseachminuteofthetimeelapsedfrom
timerstart.
Ex. one minute,
・・・
two minutes,
・・・
Itoutputsvoice20secondsbeforereachingto
thetargettime.
Ex. twenty seconds
Itiscounteddownbyvoicefrom10seconds
beforereachingtothetargettime.
Ex. ten, nine, eight
・・・
three, two, one
■↓ mode
Thevoiceoutputseachminuteofthetimeremainingup
tothealarmtime.
Ex.
・・・
ten minutes,
・・・
nine minutes,
・・・
Itoutputsvoiceevery10secondsfrom50seconds
beforereachingtothetargettime.
Ex. fty seconds,
・・・
forty seconds,
・・・
Itiscounteddownbyvoicefrom10seconds
beforereachingtothetargettime.
Ex. ten, nine, eight
・・・
three, two, one
*The voice alarm of timer is delayed from the actual time.
*During logging telemetry data, the voice alarm is delayed.
*The priority of the timer speech is higher than the telemetry
speech. Telemetry speech is stopped and the timer speech is
outputted, even if telemetry speech is outputted.
*Usually, the priority of the speech of ST1 is higher than ST2.
However, if the timer's 10-second countdown has already
begun, it is given the priority.
*The telemetry speech cannot be outputted during the
10-second countdown.