FUTABA T12K

77
<Functions of Linkage Menu>
Model deletion
*The model stored in the transmitter memory or a micro SD
card can be deleted.
*The current model cannot be deleted.
1.Movethecursortothesavedestination
display("TX"or"CARD")andpushtheRTN
buttontoswitchtothedatainputmode.
 Selectthesavedestinationbyscrollingthe
PushdialandpushtheRTNbutton.
 [TX]:Transmittermemory
 [CARD]:microSDcard
2.Movethecursortothemodelyouwantto
deleteinthemodellistandthenpushthe
RTNbutton.
3.Movethecursorto[DELETE].
4.PushtheRTNbutton.Whenaconfirmation
messageisdisplayedandtheRTNbutton
ispushedforonesecond,themodelis
deleted.
Model name change
*The model name of the model stored in the transmitter
memory or a micro SD card can be changed.
1.Ifchangingthelocation:
 Movethecursortothesavedestination
display("TX"or"CARD")andpushtheRTN
buttontoswitchtothedatainputmode.
 Selectthesavedestinationbyscrollingthe
PushdialandpushtheRTNbutton.
 [TX]:Transmittermemory
 [CARD]:microSDcard
2.Movethecursortothemodelyouwantto
changeinthemodellistandthenpushthe
RTNbutton.
3.Moveto[RENAME].
4.PushtheRTNbutton.
*The model name setup screen is displayed.
User name (candidate)
5.Changethemodelnameasdescribed
below:
 [Movingcursorintheusername(candidate)]
 Select[←]or[→],andpushtheRTNbutton.
 [Deletingacharacter]
 When[DELETE]isselectedandtheRTN
buttonispushed,thecharacterimmediately
afterthecursorisdeleted.
 [Addingacharacter]
 Whenacharacterisselectedfromthe
characterlistandtheRTNbuttonispushed,
thatcharacterisaddedattheposition
immediatelyafterthecursor.
*A name of up to 10 characters long can be entered as the
model name. (A space is also counted as one character.)
6.Afterthedesiredinformationhasbeeninput,
select[ENTER]andpushtheRTNbutton.(To
terminateinputandreturntotheoriginal
state,select[CANCEL]andpushtheRTN
button.)
Model copy
*A copy can be made of the model stored in the transmitter
memory or a micro SD card.
1.Ifchangingthelocation:
 Movethecursortothesavedestination
display("TX"or"CARD")andpushtheRTN
buttontoswitchtothedatainputmode.
 Selectthesavedestinationbyscrollingthe
PushdialandpushtheRTNbutton.
 [TX]:Transmittermemory
 [CARD]:microSDcard
2.Selectthemodelyouwanttocopyinthe
modellistandthenpushtheRTNbutton.
3.Moveto[COPY].
4.PushtheRTNbutton.
*The copy screen appears.
5.Ifreplacingthemodelstoredinthe
transmittermemory:
 Moveto[ADD-LIST]andpushtheRTNbutton
toswitchtothedatainputmode.
 Selectthedestinationmodelbyscrollingthe
PushdialandpushtheRTNbutton.
 [ADD-LIST]:addingthemodeltothelist
 [(modelname)]:replacingthemodel
*The model stored in the micro SD card can be replaced.
 Ifchangingthelocation:
 Movethecursortothecopydestination
display("TX"or"CARD")andpushtheRTN
buttontoswitchtothedatainputmode.
 Selectthesavedestinationbyscrollingthe
PushdialandpushtheRTNbutton.
6.Moveto[COPY].
7.PushtheRTNbutton.Whenaconfirmation
messageisdisplayedandtheRTNbuttonis
pushedforonesecond,themodeldatais
copied.