15
Remote control set description
• Key-Lock function guards against accidental ope-
ration
• Voice and, as applicable also MP3 file, output over
headset output or loudspeaker
• Ring-limiter: functions similar to swashplate limita-
tion but is used for control of up to three Voith-Sch-
neider drives in ship models.
• Channel sequencer for automating servo motion se-
quences of up to three servos, e. g. to automate the
lowering of landing gear or to extend/retract drives
in self-launching gliders.
Model programs
• Model type icon: graphic model type indicator
(fixed-wing / helicopter)
• Transmitter operating hours timer
• Flight phase switch assignments: six switches, two
with a priority function. Every switch combination
can be named freely. This makes the number of
flight phases independent of the number of flight
phase switches.
• Tail type normal, V-tail, Delta/flying-wing and 2 HR
Sv 3+8 (which immediately makes two coupled
elevator servos available without using free mixers
or dual mixers)
• Expanded transmitter control menu: single-sided
centre offset facility. With the exception of the trims,
all transmitter control elements can be assigned
as transmitter controls. Option of assigning two
switches to each input to act as a genuine three-
stage function.
• Wing mixers: New concept for the multi-flap menu
to simplify settings of one to eight wing servos on
a flight-phase specific basis in a comprehensible
manner without requiring the use of free mixers
• Expanded servo centre adjustment range: now +/-
125 %
• Number of flight phases: fixed-wing: 7, helicopter:
6 + AR
• Phase trim available on all axes of fixed-wing mo-
dels
• Servo assignments can be swapped at the receiver
output
Only on the
mc-20
• Flap count 4 AIL/4 FL: Full support of eight wing
servos, even without use of free mixers
• »Logical switches«: this function permits two
switches to be coupled as »and« or »or« logic
functions. The result can be employed as a virtual
switch. Typical application: The activation of certain
functions should only be possible in conjunction
with other functions, e. g. wheel brake can only be
activated when the landing gear is down. A number
of functions which are normally independent of one
another, are to be put in their base settings by way
of an »Emergency switch«. This program automa-
tion can be activated by multiple switches that also
select the appropriate program. (Standard only on
the
mc-20 HoTT, optional on the mc-16 HoTT.)
• Flight phase switching cutoff delay: the delay time
can be switched off for individual channels on a
flight-phase basis (e. g. for motor off in electric mod-
els or to activate/deactivate helicopter head lock).
(Standard only on the
mc-20 HoTT, optional on
the mc-16 HoTT.)
General HoTT features
• Simple, extremely fast binding for each model
• Ultra-fast re-binding even at maximum range
• Any number of receivers can be bound to provide
additional channels (max. 32 channels)
• Range: test and warning function
• Low-voltage warning
• GR-16 and GR-24 receivers used in SAME mode
can simultaneously address a maximum of four
servos as a block, with a frame rate of 10 ms (digital
servos only!)
• Thanks to cycle time reduced down to as lit-
tle as 10 ms, extremely short response times are
achieved.
• Real-time telemetry analysis on the transmitter
screen. As an option, telemetry data can also be
displayed on the SMART-BOX.
• Selectable cycle time: 10 ms or 20 ms/30 ms, de-
pending on receiver and operating mode
• Channel mapping in the receiver allows free distri-
bution of control functions.
The travel distance and rotation direction settings
integrated into the receiver make it possible, for ex-
ample, to match up mapped servos with one an-
other.
• The programmable fail-safe functions »Hold«, »Off«
and »Move to preset positions« that are built into
the receiver for every individual servo channel can
be set separately.
To Next Page
Loading...
Need help?
General
