Global P1: MIDI 1–1: MIDI Basic
199
Curve settings will always take effect regardless of this
setting.
PreMIDI: Velocity Curve, and Transpose will be applied to
the data that is transmitted from the KROME’s keyboard.
This means that the Velocity Curve, and Transpose settings
will affect the data that is transmitted from MIDI OUT when
the KROME’s keyboard is played, and the data that is
recorded on the internal sequencer.
MIDI data received from MIDI IN or the data played back
by the internal sequencer will not be affected.
PostMIDI: Velocity Curve, aftertouch Curve, and Transpose
will be applied to data before it enters the tone generator.
This means that the Velocity Curve, aftertouch Curve, and
Transpose settings will affect the data that is sent to the
internal tone generator when you play the KROME’s
keyboard, when the internal sequencer is played back, or
when data is received from MIDI IN.
This setting will not affect the data that is transmitted from
MIDI OUT or recorded on the internal sequencer when you
play the KROME’s keyboard or play back the sequence.
MIDI Clock:
MIDI Clock (MIDI Clock Source)
[Internal, External MIDI, External USB, Auto]
Use this setting to synchronize the KROME’s arpeggiator
and internal sequencer with an external MIDI device (e.g.,
sequencer or rhythm machine) and computer.
Internal: The arpeggiator and the internal sequencer will
operate according to the internal clock.
Select the Internal setting when using the KROME by itself,
or when you want the KROME to be the master (controlling
device) so that connected external MIDI devices will
synchronize to the KROME MIDI Clock.
External MIDI: The arpeggiator and internal sequencer will
operate in synchronization to the MIDI Clock input from an
external MIDI device.
External USB: The arpeggiator and internal sequencer will
operate in synchronization with the MIDI Clock from a
computer (for example a sequencer or DAW application),
connected to the USB connector.
Auto: Normally the operation will be the same as the
Internal setting. If external MIDI Clock messages are
received from the MIDI IN or USB connector, the KROME
will automatically switch to External MIDI and External
USB.
Note: If you select Auto when an external MIDI sequencer
and computer is connected, the KROME will automatically
switch to Internal operation if the external sequencer is not
transmitting MIDI Clock messages, allowing the arpeggiator
to operate and parameters for which MIDI/Tempo Sync is
turned on to function.
Note: If after receiving a MIDI Clock, Start, or Continue
message from the MIDI IN or USB connector, no new MIDI
Clock message is received within an interval of 500 ms, or if
you start the KROME’s sequencer from the front panel
without having received a MIDI Clock, Start, or Continue
message from the MIDI IN and USB connector, the KROME
will automatically switch to Internal operation.
Receive Ext. Realtime Commands [Off, On]
Off (unchecked): Even if MIDI Clock is set to External
MIDI, or if set to Auto and the KROME is synchronized to
external MIDI Clock messages, MIDI Common messages
and Realtime messages (Song Position Pointer, Start,
Continue, Stop) will not be received. (Song Select messages
will be received.)
Note: Use this setting if the above messages from an external
MIDI sequencer are inadvertently resetting the KROME’s
song settings.
On (checked): The above Common messages (including
Song Select) and Realtime messages will be received.
This parameter cannot be set if MIDI Clock is Internal.
Velocity
Curve=4
Aftertouch
Curve=3
Tone
generator
Play
MIDI IN
MIDI OUT
Transmitted Table
Record
Sequencer
No
Transpose
Scale
KROME
Velocity
Curve
Note number
change
Transpose
Received Table
Velocity
Curve
Aftertouch
Curve
Tone
generator
Play
MIDI IN
MIDI OUT
Record
Sequencer
Transpose
Scale
Pitch change
KROME
Velocity
Curve=4
No
Transpose
Transmitted Table Received Table
To Next Page
Loading...
