PROG P9: MFX/TFX/LFO (Master/Total Effect/LFO) 9–1: Routing
61
PROG P9: MFX/TFX/LFO (Master/Total Effect/LFO)
Here, you can make settings for the master effects and total
effect. For instance, you can:
• Route a sound to an master effects and total effect
• Make common LFO settings for effects
• Make detailed settings for master effects and total effect
For more information, please see “Effect Guide” on
page 235.
9–1: Routing
Here you can specify the type of master effects and total
effect, and turn them on/off.
The master effects are sent to the L/R bus. The total effect is
inserted into the L/R bus.
9–1a: MFX1, 2
The master effect does not output the direct sound (Dry).
Adjust the Return 1 and Return 2 return levels to return the
signal to the L/R bus and mix it with the L/R bus signal.
The master effects are stereo‐in/out, but depending on the
selected effect type, the output may be monaural. For more
information, please see “In/Out” on page 240.
MFX1:
MFX1 [000...193]
This selects the effect type for master effect 1. You can use
any of the available effects, without limitation. If you choose
000:No Effect, the output from the master effect is muted.
Category/MFX Select menu
When you press the popup button, the Category/MFX Select
menu will appear, letting you select effects by category. Use
the tabs to select a category in the menu, and then select an
effect within that category. Press the OK button to execute
your selection, or press the Cancel button to cancel.
MFX1 On/Off [Off, On]
Switches the master effect 1 on/off. When off, the output will
be muted. This will alternate between on and off each time it
is pressed.
Tip: An easy way to disable the master effects is to turn off
the front panel MASTER FX button. MFX 1/2 will be
temporarily disabled, and will stay off even if you switch
programs or modes. When you turn the switch on, the
master effects will be enabled, and you will obtain the
effects specified by the program or combination.
Note: The MASTER FX button is linked with Global P0‐1
Effect Global SW Enable MFX1&2 (see p.5).
Separately from the settings here, you can use control
change #94 to turn master effects 1 and 2 off. A value of
0 turns them off, and values of 1–127 restore the
original setting. The global MIDI channel specified by
MIDI Channel (Global 1–1a) is used for this message.
Return 1 [000...127]
This specifies the return level from the master effect to the L/
R bus.
Note: The L/R bus is sent to TFX, and then output to the
main L/MONO and R output jacks.
MFX2:
MFX2 [000...171]
MFX2 On/Off [Off, On]
Return 2 [000...127]
These parameters specify the effect type for master effect 2,
its on/off status, and the return level from master effect 2 to
the L/R bus. For more information, please see “MFX1:”
above.
MFX2 cannot use double‐size effects (172–193).
Additionally, if you select a double‐size effect for MFX1, you
won’t be able to use MFX2.
Chain:
Chain On/Off [Off, On]
On (checked): Chain (series connection) will be turned on
for MFX1 and MFX2.
Chain Direction [MFX1...MFX2, MFX2...MFX1]
Specifies the direction of the connection when MFX1 and
MFX2 are chained.
MFX1→MFX2: Connect from MFX1 to MFX2.
MFX2→MFX1: Connect from MFX2 to MFX1.
Chain Level [000...127]
When chain is On, this sets the level at which the sound is
sent from the first master effect to the next master effect.
If you select a double‐size effect, the Chain settings will
be ignored.
9–1b: TFX
These are the parameters for the total effect, which is placed
at the final stage of the L/R bus. After passing through the
total effect, the sound is output to AUDIO OUTPUT L/
MONO and R.
For the total effect, the direct sound (Dry) is always stereo‐
in/out. The input/output configuration of the effect sound
(Wet) will depend on the selected effect type.
The total effect is stereo‐in and stereo‐out, but the output
may be monaural depending on the type of effect you select.
For more information, please see “In/Out” on page 240.
TFX:
TFX [000...171]
This selects the effect type for total effect.]
TFX cannot use double‐size effects (172–193).
Category/TFX Select menu
When you press the popup button, the Category/TFX Select
menu will appear, letting you choose effect types by
category. Use the tabs to select an effect category in the
To Next Page
Loading...
