COMBI P8: Routing/IFX (Insert Effect) 8–4: IFX1
97
8–4: IFX1
This page lets you edit the detailed parameters of the five
insert effects. Use the tabs at left to select IFX1 through IFX5.
To select different effects types, use the Insert FX Setup
page. For more information, please see “8–3: Insert FX
Setup” on page 96.
8–4a: Insert Effect 1 (IFX1)
IFX1 On/Off [Off, On]
Turns the insert effect on/off. This is linked with the on/off
setting in the P8: Routing/IFX– Insert FX Setup page.
Ch (Control Channel) [Ch01...16, G ch, All-R]
This parameter specifies the MIDI channel that will be used
to control effect dynamic modulation (Dmod), pan
following the insert effect (CC#8), Send 1, and Send 2.
The channel number of the timbre routed through this IFX
will be followed by a “*” displayed at the right of Ch01–16.
If two or timbres with different MIDI channel settings are
routed through the same IFX, this parameter specifies which
of these channels will be used to control the effect.
G ch: The global MIDI Channel (Global 1–1a) will be used
to control the effect. Normally you will set this to G ch.
All-R (All Routed): The channel of any timbre routed
through this effect can be used to control the effect.
(Channels of each routed timbre will be indicated by “*”.)
Drum Kits and the MIDI Control Channel
If a Timbre is using a Drum Kit, and the Timbre’s Bus (IFX/
Output) Select (Combi 8–1(2)d) is DKit, this effects the
MIDI Control Channel as well. In this case, the Timbre’s
MIDI channel will be used to control any effect whose Ch is
set to All‐R, regardless of the Bus (IFX/Output) Select
(Global 5–5b) settings or the settings of the Drum kit IFX
Patch menu command.
P (Effect Preset)
[P00, P01...15, U00...15, ---------------]
Effect Presets let you easily store and recall all of the settings
for an individual effect. You can store up to 16 user presets
for each effect type, in addition to 15 re‐writable factory
presets.
The same presets appear in all of the modes (Program,
Combination, Sequencer).
Note that edits to effects parameters are automatically
stored with the Combi you don’t need to store them as an
Effect Preset. Presets just make it easier to re‐use your
favorite settings.
For instance, you can save an Effect Preset while working on
a particular Combination, and then later use the same Effect
Preset in a different Program, Combination, or Song.
P00: Initial Set: These are the default settings that are
recalled when you select an effect type in the Insert FX Setup
page. You can’t save your own settings here.
P01…P15: Preset data is saved in this area. We recommend
that you store your settings in U00–U15.
U00…U15: These are areas in which you can store your own
settings.
---------------: This shows that no Effect Preset has been
selected. You’ll see this if you’ve just selected an effect,
written a combination, or selected a new Combination.
Selecting this setting from the menu will not have any effect.
Note: Combis save the effects parameter settings, but they
don’t save the number of the selected Effect Preset. If you
select an Effect Preset, and then save the Combination, the
Effect Preset setting will revert to “--------------.”
For more information, please see “Using Effect Presets” on
page 60.
IFX1 Parameters:
IFX1 Parameters
Here, you can set the effect parameters of the insert effect
you chose in the Insert FX Setup page.
For more details, please see “Insert Effects (IFX1–IFX5)” on
page 240.
V
8–4: Menu Command
•0: Write Combination see p. 101
•1: Exclusive Solo see p. 64
•2: Auto Setup Song see p. 101
•3: Copy Insert Effect see p. 66
•4: Swap Insert Effect see p. 67
•5: Write FX Preset see p. 104
For more information, please see “Combination: Menu
Command” on page 101.
8–5: IFX2, 8–6: IFX3, 8–7: IFX4,
8–8: IFX5
Here you can edit the effect parameters for insert effects 2–5
selected in the Insert FX Setup page.
For more information, please see “8–4: IFX1” above.
To Next Page
Loading...
