Korg Krome - Operating Requirements: System and Controller Details

SEQ P4: Zones/Delay 4–5: Delay T01–08, 4–6: Delay T09–16
131
0: The volume will be at the original value from the bottom
velocity.
120: The volume will decrease as the velocity approaches the
bottom velocity.
Bottom Velocity [1…127]
Specifies the minimum velocity that will be sounded by each
MIDI track 1–16.
Note: You can also set the note values and velocity values by
holding down an edit cell or the ENTER button and playing
a key (see OG p.10).
Track 02...08, 09...16 (Track Number):
These are the velocity zone settings for MIDI tracks 2–8 and
9–16. They are the same as for track 1. For more information,
please see “Track 01 (Track Number):” above.
V 4–3(4): Menu Command
• 0: Memory Status see p. 163
• 1: Exclusive Solo see p. 64
• 2: Rename Song see p. 163
• 3: Delete Song see p. 163
• 4: Copy From Song see p. 163
• 5: Load Template Song see p. 163
• 6: Save Template Song (Save as User Template Song)
see p. 164
• 7: FF/REW Speed see p. 164
• 8: Set Location (Set Location for Locate Key) see p. 164
• 9: GM Initialize see p. 165
•10:
Copy from Combination see p. 166
•11: Copy from Program see p. 167
For more information, please see “Sequencer: Menu
Command” on page 163.
4–5: Delay T01–08,
4–6: Delay T09–16
This specifies the time (delay) from when the MIDI tracks 1–
8 and 9–16 receive a note‐on message until the sound begins.
4–5(6)a: Track Select, Tempo, RPPR
4–5(6)b: Track Info
For more information, please see “2–1: Trim T01–08, 2–2:
Trim T09–16” on page 123.
4–5(6)c: Delay
Track 01 (Track Number):
Delay Time [ms] [0000…5000ms, KeyOff]
Specifies the time (delay time) from note‐on until the MIDI
track begins to produce sound, in units of ms (1/1000th of a
second). This setting is available if MIDI/Tempo Sync. is set
to Off.
KeyOff: The note will begin sounding at note‐off. In this
case, the sound will not die away if the sustain level of the
program’s amp EG is other than 0. This setting is used when
creating harpsichord sounds.
Normally you will set this to 0000.
MIDI/Tempo Sync. [Off, On]
The time (delay time) from note‐on until the track produces
sound will be specified in note length units relative to the
 (Tempo).
On (checked): Specify the delay time in terms of a Base
Note and Times relative to the Tempo. For example if Base
Note = , Times = 01, and Tempo = 60 BPM, the delay time
will be equivalent to 1000 ms.
Off (unchecked): The delay time will be set by the Delay
Time setting.
Base Note [ ,   ,  ,   ,  ,   ,  ,   ,  ,  ]
Times [01...32]
It specifies the time (delay time) from note‐on until the track
begins to produce sound, in terms of a note value relative to
the  (Tempo) (Seq 0–1(2)a).
Use Base Note to specify the desired note value, and use
Times to extend that note value by the specified multiple.
For example if you set Base Note to a quarter note (  ) and
Times to 02, that track will sound with a delay of a half note
(  ). Even if you change  (Tempo) (Seq 0–1(2)a), the delay
time will always be a half note (  ). If you use these
parameters to specify a delay of a half note (  ). In this case, a
Tempo of 60.00 BPM will produce a 2000 ms delay, and a
Tempo of 120.00 BPM will produce a 1000 ms delay.
Bottom Velocity Top Velocity
Velocity
Volume
Bottom Slope
Top Slope
How volume will change according to keyboard location
4–5c
4–5a
4–5b
4–5
Menu