Combination mode
76
When a switch is assigned to a two‐state Absolute
parameter, such as Hold, the switch status directly reflects
the parameter value:
Switch On = On
Switch Off = Off
Assign
This assigns Tone Adjust parameters to the switches in the
display. For a full list of the available choices, please see
“Common Tone Adjust Parameters” on page 9 and “Tone
Adjust Parameters” on page 10.
On Value [Depends on parameter]
The parameter is set to this value when the switch is On.
When the switch is assigned to a two‐state Absolute
parameter, such as Hold, this will always be the same as the
Switch Status (see below).
Switch Status [Off, On]
This simply shows whether the switch is On or Off.
Sliders 1–8
Assign
This assigns Tone Adjust parameters to the sliders in the
display. For a full list of the available choices, please see
“Common Tone Adjust Parameters” on page 9 and “Tone
Adjust Parameters” on page 10.
Assignments are exclusive
Per‐Oscillator parameters apply to OSC1 and 2 individually,
and are marked as such: OSC1 and OSC2.
Each slider can be assigned to only one parameter, and each
parameter can be assigned to only one slider.
To swap a parameter from one slider to another, you’ll need
to first un‐assign it from the old slider, and then assign it to
the new slider.
Value
This shows the current value of the parameter. The range of
values will vary depending on the parameter assigned to the
slider.
V
0–7: Menu Command
•0: Write Combination see p. 101
•1: Exclusive Solo see p. 64
•2: Auto Song Setup see p. 65
•3: Copy from Program see p. 101
•4: Copy Tone Adjust see p. 102
•5 Reset Tone Adjust see p. 103
For more information, please see “Combination: Menu
Command” on page 101.
Controls
REALTIME CONTROLS lets you use knobs [1]–[4] to
modify the parameters of the combination or the effects. You
can also use these knobs to control the arpeggiators. When
you use a knob, the display will show the controller’s
function and value. Use the SELECT button to change the
knob functions.
In TONE, the functions assigned to knobs 1–4 are fixed.
In USER, you can assign a variety of modulation functions
to knobs 1–4. To assign functions, use the P1: Controllers
Setup page (page 78).
Realtime Controls
The Realtime Controls TONE knob functions (CUTOFF – EG
RELEASE) are fixed. You can assign a variety of functions to
Realtime Controls USER knobs 1–4 (USER [1]–USER [4]).
MIDI control changes are assigned for each function.
When you move a knob, it sends out the corresponding
MIDI CC.
This will control timbres on the global MIDI channel.
Most of these functions adjust (scale) the parameter settings
of the timbre programs. Unless otherwise noted, “scaling”
means that the parameters are at their programmed values
when the controller is at 64, at their minimum when the
controller is at 0, and at their maximum when the controller
is at 127. For another look at this, please see the diagram
below.
CC parameter scaling
TONE [Cut Off]: Flt Fc (Cutoff) [000...127]
This knob scales the cutoff frequencies of Filters A and B,
and transmits and receives MIDI CC #74.
TONE [RESONANCE]: Flt Reso (Resonance)
[000...127]
This knob scales the resonance of Filters A and B, and
transmits and receives MIDI CC #71.
TONE [EG INTENSITY]: Flt EG (Filter EG Intensity)
[000...127]
This knob scales the effect of the Filter EG on the cutoff
frequencies of Filters A and B. It also transmits and receives
MIDI CC#79.
TONE [RELEASE]: EG Rel (EG Release) [000...127]
This knob scales the release time of the Filter and Amp EGs,
and transmits and receives MIDI CC#72.
USER [1]…[4] [000...127]
These are the current values and assigned functions (MIDI
CC) for the Realtime Controls USER knobs.
99
00
640 127
CC Value
Parameter
Value
As Programmed
To Next Page
Loading...
