Sequencer mode
126
3–3: OSC T01–08,
3–4: OSC T09–16
These parameters specify how each MIDI track will be
sounded.
3–3(4)a:Location, Meter, Tempo, Tempo
Mode, Song Select, Track Select,
Reso, RPPR
3–3(4)b:Track Info
For more information, please see “0–1(2)a: Location, Meter,
Tempo, Tempo Mode, Song Select, Track Select, Reso, RPPR”
on page 109.
For more information, please see “2–1: Trim T01–08, 2–2:
Trim T09–16” on page 123.
3–3(4)c: OSC
Track 01 (Track Number):
Force OSC Mode [PRG, Poly, MN, LGT]
This lets you override the Program’s stored Voice Assign
Mode settings, if desired.
PRG: The Program’s stored Prog P1: Basic/Controllers–
Program Basic Voice Assign Mode settings will be used.
Poly: The track will play polyphonically, regardless of the
Program’s settings.
MN (Mono): The track will play monophonically, regardless
of the Program’s settings.
LGT (Legato): The track program will sound
monophonically, and will play legato according to the
Program’s Mode setting (Prog 1–1b).
With the MN or LGT settings, the Program’s Priority setting
(Prog 1–1b) will determine the priority of the note that
sounds when you play two or more notes.
OSC Select [BTH, OS1, OS2]
Specifies whether the MIDI track’s program will play OSC1,
OSC2, or both.
For programs whose Oscillator Mode (Prog 1–1a) is Double
or Double Drums, this setting lets you specify that only
OSC1 or OSC2 will sound.
BTH (Both): OSC1 and 2 will sound as specified by the
settings of the program.
OS1: Only OSC1 will sound.
OS2: Only OSC2 will sound. PCM programs will not sound
if Oscillator Mode is set to Single or Drums.
Portamento [PRG, Off, 001...127]
Make portamento settings for each MIDI track.
The portamento setting you make here will be used when
the song is played or recorded from the beginning. If you
change the setting while recording, it will be recorded as
part of the musical data. (However if you set this to PRG, it
will not be recorded.) You can change this setting during
playback. However if you play back any Portamento On/Off
data or Portamento Time data that was previously recorded,
the settings will change accordingly.
When the track whose Status (Seq 3–1(2)c) is INT or BTH,
MIDI control change CC#05 (Portamento Time) and CC#65
(Portamento Switch) can be received to control this and
change the setting. (If the setting is PRG, CC#05 Portamento
Time will not be received.)
When you switch songs or return to the beginning of the
song, tracks whose Status is BTH, EXT, or EX2 will transmit
this setting via MIDI. If this is Off, CC#65 with a value of 0
will be transmitted. If this is 001–127, a CC#65 of 127 and
CC#05 of 1–127 will be transmitted.
If this is set to PRG, nothing will be transmitted.
This data is transmitted and received on the MIDI channel
specified for each track by MIDI Channel (Seq 3–1(2)c). (See
Global P1: MIDI, SEQ Mode “Track MIDI Out” on page 200)
Track 02...08, 09...16 (Track Number):
Here, you can make OSC settings for MIDI tracks 2–8 and 9–
16. They are the same as for track 1. For more information,
please see “Track 01 (Track Number):” above.
V
3–3(4): Menu Command
•0: Memory Status see p. 163
•1: Exclusive Solo see p. 64
•2: Rename Song see p. 163
•3: Delete Song see p. 163
•4: Copy From Song see p. 163
•5: Load Template Song see p. 163
•6: Save Template Song (Save as User Template Song)
see p. 164
•7: FF/REW Speed see p. 164
•8: Set Location (Set Location for Locate Key) see p. 164
•9: GM Initialize see p. 165
•10:
Copy from Combination
see p. 166
• 11: Copy from Program see p. 167
For more information, please see “Sequencer: Menu
Command” on page 163.
To Next Page
Loading...
