256
You can configure a 21‐Band Graphic EQ ranging from 80
Hz to 18 kHz if you route three Graphic 7‐Band EQ effects in
series, with a setting of 7:Low, 9:Mid, and 11:High for each
EQ.
009: St.Exciter/Enhncr (Stereo
Exciter/Enhancer)
This effect is a combination of the Exciter, which adds a
punch to the sound and the Enhancer, which adds spread
and presence.
a: Exciter Blend
This parameter sets the depth (intensity) of the Exciter effect.
Positive values give a frequency pattern (to be emphasized)
different from negative values.
b: Emphasis Frequency
This parameter sets the frequency to be emphasized. Higher
values will emphasize lower frequencies.
c: Enhancer Delay L [msec]
d: Enhancer Delay R [msec]
These parameters set the delay time for the Enhancer left
and right channel. Specifying a slightly different delay time
for the left and right channel will add a stereo image, depth,
and width to the sound.
010: Stereo Isolator
This is a stereo effect that separates the input signal into low,
mid, and high‐frequency bands, and controls the volume of
each band independently. For example you can separately
boost or cut the kick, snare, and hi‐hat sounds from a drum
signal in realtime.
a
Exciter Blend –100...+100
Sets the intensity (depth) of the
Exciter effect p.256
Src Off...Tempo
Selects the modulation source of
the Exciter intensity
Amt –100...+100
Sets the modulation amount of
the Exciter intensity
b
Emphasis
Frequency
0...70
Sets the frequency to be empha-
sized p.256
Src Off...Tempo
Selects the modulation source of
the frequency to be emphasized
Amt –70...+70
Sets the amount of modulation
of the frequency to be empha-
sized
c
Enhancer
Delay L
[msec]
0.0...50.0
Sets the delay time for the
Enhancer left channel p.256
d
Enhancer
Delay R
[msec]
0.0...50.0
Sets the delay time for the
Enhancer right channel p.256
e
Enhancer
Depth
0...100
Sets the determines to what
degree the Enhancer effect is
applied
Src Off...Tempo
Selects the modulation source of
the Enhancer width
Amt –100...+100
Sets the modulation amount of
the Enhancer width
f EQ Trim 0...100 Sets the 2-band EQ input level
g
Pre LEQ Fc
Low,
Mid-Low
Selects the cutoff frequency (low
or mid-low) of the low-range
equalizer
Pre HEQ Fc
High,
Mid-High
Selects the cutoff frequency
(high or mid-high) of the high-
range equalizer
h
Pre LEQ Gain
[dB]
–15.0...+15.0 Sets the gain of the Low EQ
Pre HEQ Gain
[dB]
–15.0...+15.0 Sets the gain of the High EQ
i
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
EQ Trim
LEQ HEQ
EQ Trim
Delay
Delay
Depth
D
-mod
Exciter
Exciter
Enhancer
a Trim 0...100 Sets the input level
b Low/Mid [Hz] 100...500
Sets the frequency at which the
low and mid bands are divided
c
Mid/High
[Hz]
2000...6000
Sets the frequency at which the
mid and high bands are divided
d
Low Gain [dB]
–Inf,
–59...+12
Sets the low-frequency gain
Src Off...Tempo
Selects the source that will
modulate low-frequency gain
Amt –72...+72
Sets the amount by which the
low-frequency gain will be
modulated
e
Mid Gain [dB]
–Inf,
–59...+12
Sets the mid-frequency gain
Src Off...Tempo
Selects the modulation source
for mid-frequency gain
Amt –72...+72
Sets the amount by which the
mid-frequency gain will be
modulated
f
High Gain
[dB]
–Inf,
–59...+12
Sets the high-frequency gain
Src Off...Tempo
Selects the modulation source
for high-frequency gain
Amt –72...+72
Sets the amount by which the
high-frequency gain will be
modulated
g
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
D
-mod
D
-mod
D
-mod
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Trim
Isolator
Low
Mid
High
Trim
Low
Mid
High
To Next Page
Loading...
