Korg Krome - Dynamics (Dynamic); 000: no Effect; 001: Stereo Compressor; 002: Red Comp

Dynamics (Dynamic) 000: No Effect
251
Dynamics (Dynamic)
000: No Effect
Select this option when you do not use any effects. The
Insert Effect/Total Effect section outputs unprocessed
signals and the Master Effect section mutes the output.
001: Stereo Compressor
This effect compresses the input signal to regulate the level
and give a “punchy” effect. It is useful for guitar, piano, and
drum sounds. This is a stereo compressor. You can link left
and right channels, or use each channel separately.
a: Envelope Select
This parameter selects whether the left and right channels
are linked to control both signals simultaneously, or whether
each channel is controlled independently.
b: Sensitivity
g: Output Level (Level)
The Sensitivity parameter sets the sensitivity of the
compressor. If this parameter is set to a higher value, lower
level sounds will be boosted. With a higher Sensitivity, the
overall volume level is higher. To adjust the final volume
level, use the Output Level parameter.
c: Attack
This parameter controls the attack level.
002: Red Comp
When playing chords on an electric piano or similar
instrument, it’s helpful to use a compressor to keep each
note smooth and well‐balanced. In addition to a distinctive
percussive accent, it will also provide a long sustain. This
effect models a popular compressor with a clean sound
that’s perfect for pop and funk music.
a
Envelope
Select
L/R Mix,
L/R Individ-
ually
Determines whether the left and
right channels are linked or used
separately
b Sensitivity 1...100 Sets the sensitivity
c Attack 1...100 Sets the attack level
d EQ Trim 0...100 Sets the EQ input level
e
Pre LEQ Fc
Low,
Mid-Low
Selects the cutoff frequency (low
or mid-low) of the low-range
equalizer
Pre HEQ Fc
High,
Mid-High
Selects the cutoff frequency
(high or mid-high) of the high-
range equalizer
f
Pre LEQ Gain
[dB]
–15.0...+15.0 Sets the gain of the Low EQ
Pre HEQ Gain
[dB]
–15.0...+15.0 Sets the gain of the High EQ
g
Output Level 0...100
Sets the output level of the
compressor
Src Off...Tempo
Selects the modulation source
for the compressor output level
Amt –100...+100
Sets the modulation amount for
the compressor output level
h
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
EQ Trim
EQ Trim
LEQ HEQ
LEQ
HEQ
Compressor
Compressor
Envelope Select
Output Level
Output Level
Envelope - Control
Envelope - Control
a Sensitivity 1...100 Sets the sensitivity p.251
b Attack 1...100 Sets the attack level p.251
c
Level 0...100
Sets the output level of the
compressor p.251
Src Off...Tempo
Selects the modulation source
for Level
Amt –100...+100
Sets the modulation amount for
Level
d
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects the modulation source
for Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
Sensitivity=100
Sensitivity=40
Dry
Wet
Time
Level
Compressor - Sensitivity
Louder
Dry
Wet
Time
Level
Attack=80
Attack=20
Compressor - Attack
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Right
Wet / Dry
Wet / Dry
+
Envelope - Control
Output Level
Compressor