Sequencer mode
150
8–4: IFX1
Here, you can edit the parameters of the insert effect 1 you
selected in the P8: Routing/IFX– Insert FX Setup page.
8–4a: Insert Effect 1 (IFX1)
IFX On/Off [Off, On]
Turns the insert effect on/off. This is linked with the On/Off
setting in the P8: Routing/IFX– Insert FX Setup page.
Ch (Control Channel) [Ch01...16, All-R]
This specifies the MIDI channel that will control dynamic
modulation (Dmod) for the insert effect.
Ch01...Ch16: The insert effect will be controlled on the
specified MIDI channel.
All-R: The channel of any track routed through this effect
can be used to control the effect. (Channels of each routed
track will be indicated by “*”.)
Drum Kits and the MIDI Control Channel
If a Track is using a Drum Kit, and the Track’s Bus (IFX/
Output) Select (Seq 8–1(2)d) is DKit, this affects the
MIDI Control Channel as well. In this case, the Track’s
MIDI channel will be used to control any effect whose
Ch is set to All‐R, regardless of the Bus (IFX/Output)
Select (Global 5–5b) settings or the settings of the
DrumKit IFX Patch menu command.
P (Effect Preset)
[P00, P01...15, U00...15, ---------------]
Effect Presets let you easily store and recall all of the settings
for an individual effect. You can store up to 16 user presets
for each effect type, in addition to 15 re‐writable factory
presets.
The same presets appear in all of the modes (Program,
Combination, Sequencer).
Note that edits to effects parameters are automatically
stored with the Song–you don’t need to store them as an
Effect Preset. Presets just make it easier to re‐use your
favorite settings.
For instance, you can save an Effect Preset while working on
a particular Song, and then later use the same Effect Preset
in a different Program, Combination, or Song.
P00: Initial Set: These are the default settings that are
recalled when you select an effect type in the Insert FX Setup
page. You can’t save your own settings here.
P01…P15: Preset data is saved in this area. We recommend
that you store your settings in U00–U15.
U00…U15: These are areas in which you can store your own
settings.
---------------: This shows that no Effect Preset has been
selected. You’ll see this if you’ve just selected an effect or
selected a new Song. Selecting this setting from the menu
will not have any effect.
Note: Songs save the effects parameter settings, but they
don’t save the number of the selected Effect Preset. If you
select an Effect Preset, save the Song to media, and then re‐
load the Song, the Effect Preset setting will revert to “---------
-----.”
For more information, please see “Using Effect Presets” on
page 60.
IFX1 Parameters:
IFX Parameters
Here, you can set the effect parameters of the insert effect
you chose in the P8–3: Insert FX Setup page.
For more information, please see “Insert Effects (IFX1–
IFX5)” on page 240.
V
8–4: Menu Command
•0: Memory Status see p. 163
•1: Exclusive Solo see p. 64
•2: Copy Insert Effect see p. 66
•3: Swap Insert Effect see p. 67
•4:Write FX Preset see p. 184
•5: FF/REW Speed see p. 164
•6: Set Location (Set Location for Locate Key) see p. 164
•7: Put Effect Setting to Track see p. 184
For more information, please see “Sequencer: Menu
Command” on page 163.
8–5: IFX2, 8–6: IFX3, 8–7: IFX4,
8–8: IFX5
Here, you can edit the effect parameters for insert effects 2–5
selected in the Insert FX Setup page.
For more information, please see “8–4: IFX1” above.
8–9: FX Control T01–08,
8–10: FX Control T09–16
Here, you can specify the buses, and effect control bus, for
the outputs of tracks 1–8 and 9–16.
8–9(10)a: Routing Map
8–9(10)b: Track Select, Tempo, RPPR
8–9(10)c: Track Info
For more information, please see “8–1(2)a: Routing Map” on
page 148 and “2–1: Trim T01–08, 2–2: Trim T09–16” on
page 123.
To Next Page
Loading...
