Chorus, Flanger, and Phaser (Cho/Fln Phaser) 031: Black Chorus
269
031: Black Chorus
This models a Danish‐made stereo chorus + pitch modulator
& flanger. Although this effect was originally intended for
guitar, it was also used by numerous keyboard players.
Used with electric piano, it produces a distinctive tone.
c: Mode
b: Intensity
Increasing the Intensity value will strengthen the
modulation effect. This controls the effect, direct, and
feedback values. The values that are controlled will depend
on the Mode setting.
032: EP Chorus
This is inspired by a rare chorus built into an early version of
a famous modified tine piano.
033: St.HarmonicChorus
(Stereo Harmonic Chorus)
This effect applies chorus only to higher frequencies. This
can be used to apply a chorus effect to a bass sound without
making the sound thinner. You can also use this chorus
block with feedback as a flanger.
g: High/Low Split Point
This parameter sets the frequency that splits the high and
low range. Only the high range will be sent to the chorus
block.
a
Speed [Hz] 0.10...10.0 Sets the LFO speed
Src Off...Tempo
Selects a modulation source for
Speed [Hz]
Amt –100...+100
Sets the modulation amount for
Speed [Hz]
b Intensity 1...100
Sets the intensity of LFO
modulation
c Mode 0, 1, 2
Select a mode
0: Chorus
1: Pitch Modulation
2: Flanger
d Width 0...100 Sets the LFO modulation depth
e Input Gain 1...100 Sets the input gain
f Output Mode 0, 1
Select a output mode
0: Mono
1: Stereo
g
Wet/Dry
Dry, 1:99 ...
99:1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100 ... +100
Sets the modulation amount for
Wet/Dry
a
Speed [Hz] 0.10...10.0 Sets the LFO speed p.259
Src Off...Tempo
Selects a modulation source for
Speed [Hz]
Amt –100...+100
Sets the modulation amount for
Speed [Hz]
b
Depth 0...100
Sets the depth of LFO
modulation
Src Off...Tempo
Selects the modulation source of
the LFO modulation depth
Amt –100...+100
Sets the modulation amount of
the LFO modulation depth
c
Wet/Dry
Dry,
1:99…99:1,
Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100…+100
Sets the modulation amount for
Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Chorus
LFO
Input Gain
Mode & Intensity
Mono
Stereo
Output Mode
-
+
+
+
a
LFO
Waveform
Triangle, Sine Selects the LFO Waveform
LFO Phase
[degree]
–180...+180
Sets the LFO phase difference
between the left and right
p.259
b
LFO
Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO p.259
Src Off...Tempo
Selects a modulation source for
LFO speed
Amt
–20.00...
+20.00
Sets the modulation amount of
LFO speed
c
MIDI Sync Off, On
When this is on, the LFO speed is
set by BPM, Base Note, and
Times, instead of Frequency
p.257
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo;
40–300 sets the tempo manually
for this individual effect p.257
Base Note ...
Selects the type of notes that
specify the LFO speed p.257
Times x1...x32
Sets the number of notes that
specify the LFO speed p.257
d
LFO Type
Individual,
Common1,
Common2
Selects either (individual) LFO,
Common FX LFO1, or Common
LFO2 p.257
Common
LFO Offset
[deg]
–180...+180
Sets the phase offset when Type
= Common 1 or Common 2
p.257
e
Pre Delay
[msec]
0.0...50.0
Sets the delay time from the
original sound
f
Depth 0...100
Sets the depth of LFO
modulation
Src Off...Tempo
Selects the modulation source of
the LFO modulation depth
Amt –100...+100
Sets the modulation amount of
the LFO modulation depth
g
High/Low
Split Point
1...100
Sets the frequency split point
between the low and high range
p.269
h
Feedback –100...+100
Sets the feed back amount of the
chorus block p.270
High Damp
[%]
0...100
Sets the high range damping
amount of the chorus block
i
Low Level 0...100 Sets the low range output level
High Level 0...100
Sets the high range (chorus)
output level
j
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
We
t
/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
Left
Right
Feedback
LFO Phase
LFO: Tri / Sine
Wet / Dry
Wet / Dry
High Damp
Stereo In - Stereo Out
Low Level
Low Level
High Level
High Level
High/Low Split Point
High Damp
Chorus/Flanger
Chorus/Flanger
To Next Page
Loading...
