COMBI P4: Zone/Delay 4–3: Vel Zone T01–08, 4–4: Vel Zone T09–16 (Velocity Zones T01–08, T09–16)
85
a key (see OG p.10).
It is not possible to set the bottom key above the top key
of the same timbre. Nor is it possible for the top and
bottom slopes to overlap.
Timbre 02...08, 09...16 (Timbre Number):
These are the key zone settings for timbres 2–8 and 9–16.
They are the same as for timbre 1. For more information,
please see “Timbre 01 (Timbre Number):” above.
V
4–1(2): Menu Command
• 0: Write Combination see p. 101
• 1: Exclusive Solo see p. 64
• 2: Auto Song Setup see p. 65
• 3: Copy from Program see p. 101
For more information, please see “Combination: Menu
Command” on page 101.
4–3: Vel Zone T01–08,
4–4: Vel Zone T09–16
(Velocity Zones T01–08, T09–16)
Sets the Top/Bottom Velocity parameters to specify the
range of velocities that will sound for each timbre 1–8 and 9–
16, and set the Top/Bottom Slope parameters to specify the
range over which the volume will change.
Velocity switch: If you set different velocity zones for
multiple timbres so that they do not sound together, you can
play separate sounds by varying playing dynamics.
Layer: If you set two or more timbres to velocity zones that
overlap, the sounds will be heard together.
Velocity Cross-fade: If the slope ranges (gray line) overlap,
different sounds will be sounded together, and your playing
dynamics will determine the proportion of each sound.
It is not possible to set the bottom velocity greater than
the top velocity for the same timbre, nor can the top
slope and the bottom slope overlap.
4–3(4)a: Zone Map
This area indicates the note and velocity ranges in which
each timbre will sound.
For more information, please see “4–1(2)a: Zone Map” on
page 84.
4–3(4)b: Combination Name, Tempo
4–3(4)c: Timbre Info
For more information, please see “2–1: EQ Trim T01–08, 2–2:
EQ Trim T09–16” on page 79.
4–3(4)d: Velocity Zones
Timbre 01 (Timbre Number):
Top Velocity [001…127]
Specifies the maximum velocity value that will sound each
timbre.
Top Slope [000…120]
Specifies the number of velocity steps over which the
original volume will be reached, starting from the Top
Velocity.
0: The volume will be at the original value from the top
velocity.
120: The volume will decrease as the velocity approaches the
top velocity.
Bottom Slope [000…120]
Specifies the number of velocity steps over which the
original volume will be reached, starting from the Bottom
Velocity.
0: The volume will be at the original value from the bottom
velocity.
120: The volume will decrease as the velocity approaches the
bottom velocity.
Bottom Velocity [001…127]
Specifies the minimum velocity value that will sound each
timbre.
Note: You can also set the note values and velocity values by
holding down an edit cell or the ENTER button and playing
a key (see OG p.10).
Timbre 02...08, 09...16 (Timbre Number):
These are the velocity zone settings for timbres 2–8 and 9–
16. They are the same as for timbre 1. For more information,
please see “Timbre 01 (Timbre Number):” above.
V
4–3(4): Menu Command
•0: Write Combination see p. 101
•1: Exclusive Solo see p. 64
•2: Auto Song Setup see p. 65
•3: Copy from Program see p. 101
For more information, please see “Combination: Menu
Command” on page 101.
Bottom Velocity Top Velocity
Velocity
Volume
Bottom Slope
Top Slope
How volume will change according to keyboard location
To Next Page
Loading...
