Korg Krome - 054: Grain Shifter

280
a: Scratch Source
b: Response
The Scratch Source parameter enables you to select the
modulation source that controls simulation. The value of the
modulation source corresponds to the playback position.
The Response parameter enables you to set the speed of the
response to the modulation source.
c: Envelope Select
c: Src
d: Threshold
When Envelope Select is set to D‐mod, the input signal will
be recorded only when the modulation source value is 64 or
higher.
When Envelope Select is set to Input, the input signal will
be recorded only when its level is over the Threshold value.
The maximum recording time is 2,730msec. If this is
exceeded, the recorded data will start being erased from the
top.
e: Response
This parameter enables you to set the speed of the response
to the end of recording. Set a smaller value when you are
recording a phrase or rhythm pattern, and set a higher value
if you are recording only one note.
f: Direct Mix
With Always On, a dry sound is usually output. With
Always Off, dry sounds are not output. With Cross Fade, a
dry sound is usually output, and it is muted only when
scratching.
Set Wet/Dry to Wet to use this parameter effectively.
054: Grain Shifter
This effect cuts extremely short samples (“grains”) from the
input signal waveform and plays them repeatedly, giving a
mechanical character to the sound.
a: Duration
c: LFO Sample Cycle [Hz]
Duration sets the length of the sampled grain, and the LFO
Sample Cycle controls how often a new grain is sampled. In
between Sample Cycles, the current grain is repeated
continuously.
d Threshold 0...100
Sets the recording start level
when Envelope Select is set to
Input p.280
e Response 0...100
Sets the speed of the response
to the end of recording p.280
f Direct Mix
Always On,
Always Off,
Cross Fade
Selects how a dry sound is mixed
p.280
g
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
+ Max
Zero
Scratch!
D
-mod
– Max
JS X
JS+Y
JS–Y
etc…
Zero
+ Max
Scratch Source
Recorded Sound
Scratch Source
Start Playback Position End
a
Duration 0...100
Sets the duration of the grain
p.280
Src Off...Tempo
Selects the source that will
modulate the duration of the
grain
Amt –100...+100
Sets the amount by which the
grain duration will be modulated
b LFO Sync Src Off...Tempo
Selects the modulation source
that will reset the LFO
c
LFO Sample
Cycle [Hz]
0.02...20.00
Sets the frequency at which the
grain will be switched p.280
Src Off...Tempo
Selects a modulation source for
LFO speed
Amt
–20.00...
+20.00
Sets the modulation amount of
LFO speed
d
MIDI Sync Off, On
When this is on, the LFO speed is
set by BPM, Base Note, and
Times, instead of Frequency
p.257
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo;
40–300 sets the tempo manually
for this individual effect p.257
Base Note ...
Selects the type of notes that
specify the LFO speed p.257
Times x1...x32
Sets the number of notes that
specify the LFO speed p.257
e
LFO Type
Individual,
Common1,
Common2
Selects either (individual) LFO,
Common FX LFO1, or Common
LFO2 p.257
Common
LFO Offset
[deg]
–180...+180
Sets the phase offset when Type
= Common 1 or Common 2
p.257
f
Wet/Dry
Dry, 1: 99... 99
: 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
+
Left
Right
Sample Cycle
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
LFO
D
-mod
Trigger
Grain Shifter
In
Out
Sample Cycle / Duration
Sample Cycle
Duration