Korg Krome - 184: St. Pitch Shifter (Stereo Pitch Shifter)

332
b, c, d, e, f, g: Status
These parameters set the output status of each Tap.
Always On: Output is always on. (No modulation)
Always Off: Output is always off. (No modulation)
On→Off (dm): Output level is switched from on to off
depending on the modulation source.
Off→On (dm): Output level is switched from off to on
depending on the modulation source.
Combining these parameters, you can change from 4‐phase
chorus to two‐tap delay by crossfading them gradually via
the modulation source during a performance.
h: Panning Preset
This parameter selects combinations of stereo images of the
tap outputs.
184: St. Pitch Shifter (Stereo
Pitch Shifter)
This is a stereo pitch shifter. The pitch shift amount for the
left and right channels can be reversed from each other.
a: L/R Pitch
When you select Up/Down for this parameter, the pitch shift
amount for the right channel will be reversed. If the pitch
shift amount is positive, the pitch of the left channel is
raised, and the pitch of the right channel is lowered.
h
Panning
Preset
1 : L 1 2 3 4 5
6 R,
2 : L 135 246 R,
3 : L 1 3 5 2 4
6 R,
4 : L 1 4 5 6 3
2 R
Selects the stereo panning
pattern for each tap
p.332
i
Tap1
Feedback
–100...+100 Sets the Tap1 feedback amount
Src Off...Tempo
Selects the modulation source
for the Tap output level,
feedback amount, and effect
balance
Amt –100...+100
Sets the modulation amount of
Tap1 feedback amount
j
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
a
Mode
Slow,
Medium, Fast
Switches Pitch Shifter mode
p.287
L/R Pitch
Normal,
Up/Down
Determines whether or not the
L/R pitch shift amount is inverted
p.332
b
Pitch Shift [1/
2tone]
–24...+24
Sets the pitch shift amount in
steps of a semitone p.285
Src Off...Tempo
Selects the modulation source of
pitch shift amount p.285
Amt –24...+24
Sets the modulation amount of
pitch shift amount p.285
c
Fine [cent] –100...+100
Sets the pitch shift amount in
steps of one cent p.285
Amt –100...+100
Sets the modulation amount of
pitch shift amount p.285
d
L Delay
[msec]
0...2000
Sets the delay time for the left
channel
e
R Delay
[msec]
0...2000
Sets the delay time for the right
channel
f
Feedback –100...+100
Sets the feedback amount
p.285
High Damp
[%]
0...100
Sets the damping amount in the
high range
g
Feedback
Position
Pre, Post
Switches the feedback
connection p.285
Spread –100...+100
Sets the width of the stereo
image of the effect sound
p.289
h
Input Level
D-mod [%]
–100...+100
Sets the modulation amount of
the input level p.284
Src Off...Tempo
Selects the modulation source
for the input level p.284
i
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
Left
Right
Feedback
Spread
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
High Damp
High Damp
Input Level
Input Level
Feedback Position
Pre
Pre
Post
Post
Delay
Pitch Shifter
Delay
Pitch Shifter