Global mode
200
SEQ Mode:
Track MIDI Out
[for Master, for External Sequencer]
This setting specifies what will be transmitted via MIDI
when you switch songs in Sequencer mode.
for Master: Normally in Sequencer mode, the internal
sequencer can record or play back a performance on the
KROME’s keyboard. In this case, tracks that are set to EXT or
BTH will control external MIDI sound modules. You can
make settings in a song so that when you select that song on
the KROME, tracks that are set to EXT or BTH will transmit
program changes or other MIDI messages* to set up your
external MIDI sound modules.
for External Sequencer: Choose this setting if you want to
use the KROME in Sequencer mode as a multi‐timbral
sound module driven by an external sequencer. With this
setting, even the tracks that are set to EXT or BTH will not
transmit program changes or other MIDI messages* when
you switch songs on the KROME. In this case, echo‐back
from the external MIDI sequencer will not switch programs
or other parameters to the identical settings on each track
that is set to the same MIDI channel.
* Applicable parameters
• Program Select: CC#00 bank select (LSB), CC#32 bank
select (MSB), program change
• Pan: CC#10 pan
• Volume: CC#7 volume
• Portamento: CC#65 portamento On/Off, CC#5 portamento
time
• Send 1/2: CC#93 send 1 level, CC#91 send 2 level
• (Post FX) Pan: CC#8 post insert effect pan
Param. MIDI Out
[Control Change, SysEx-Param Change]
This setting specifies whether control changes or System
Exclusive messages will be transmitted when you edit a
parameter in Sequencer mode.
Control Change: Data for the edited parameter will be
transmitted as a control change.
SysEx-Param Change: Data for the edited parameter will be
transmitted as a parameter change.
Note: For these to operate, Enable Control Change or
Enable Exclusive (Global P1: MIDI– MIDI Routing) must be
checked respectively.
* Applicable parameters
• Pan: CC#10 pan
• Volume: CC#7 volume
• Send 1/2: CC#93 send 1 level, CC#91 send 2 level
Drum Track:
Drum track programs in Program mode will be triggered on
the global MIDI channel if Trigger Mode is set to Wait KBD
Trig. The MIDI transmit channel is specified by the Drum
Track Prog MIDI Ch. Use the Drum Track Prog MIDI Out
to specify whether the MIDI note data of the pattern will be
transmitted.
Drum track programs do not transmit or receive MIDI
program changes.
Prog MIDI Ch [01…16]
This specifies the MIDI channel for drum track transmission
and reception in Program mode. If Prog MIDI Out is
checked, drum pattern note data will be transmitted on this
MIDI channel. The default setting is channel 10.
Prog MIDI Out [Off, On]
On (checked): The note data of the drum track pattern will
be transmitted on the channel specified by Prog MIDI Ch.
Off (unchecked): The note data of the drum track pattern
will not be transmitted.
V
1–1: Menu Command
•0: Write Global Setting see p. 216
•1: Dump Program see p. 218
•2: Dump Combination see p. 218
•3: Dump Drum Kit see p. 218
•4: Dump Arpeggio Pattern see p. 218
•5: Dump Global Setting see p. 218
•6: Dump Sequencer see p. 218
•7: Dump Drum Track Pattern see p. 218
For more information, please see “Global: Menu Command”
on page 216.
1–2: MIDI Routing
Here, you can make MIDI Routing and MIDI Filter settings
for the entire KROME.
Note: To transmit MIDI exclusive dump data, you’ll use the
menu commands of the P1: MIDI page.
1–2a: MIDI Routing
ARP Controllers MIDI Out
[Control Change, SysEx-Param Change]
This specifies the MIDI messages that will be transmitted
when you operate the ARP button or when you operate
knobs 1–4 with ARP selected by SELECT swtich.
Control Change: Operating the ARP button or knobs 1–4
will transmit the MIDI control change messages that are
assigned in Global P2–2: Controllers (SW) – ARP ON/OFF
and (ARP CONTROL) GATE – (ARP CONTROL) STEP.
SysEx-Param Change: Operating the ARP button or knobs
1–4 will transmit MIDI System Exclusive parameter change
messages for the parameters (arpeggiator on/off, Gate,
Ve loc it y, Swing, Step) assigned to the button and knobs.
1–2b: MIDI Filter
Enable Program Change [Off, On]
On (checked): Program changes will be transmitted and
received.
In Program mode (P0: Play), the program will be switched
when a program change message is received on the global
MIDI channel specified by MIDI Channel (Global 1–1a).
When you switch programs, a program change message will
be transmitted on the global MIDI channel.
To Next Page
Loading...
