Modulation and Pitch Shift (Mod./P.Shift) 052: Doppler
279
g: High Damp [%]
i: High Damp [%]
This sets the amount of damping amount for the high
frequencies of the resonant sound. Lower values create a
metallic sound with a higher range of harmonics.
052: Doppler
This effect simulates the “Doppler effect” of a moving sound
with a changing pitch, similar to the siren of an passing
ambulance. Mixing the effect sound with the dry sound will
create a unique chorus effect.
a: LFO Mode
a: Src
b: LFO Sync
The LFO Mode parameter switches LFO operation mode.
When Loop is selected, the Doppler effect will be created
repeatedly. If LFO Sync is set to On, the LFO will be reset
when the modulation source specified with the Src
parameter is turned on.
When LFO Mode is set to 1‐Shot, the Doppler effect is
created only once when the modulation source specified in
the Src field is turned on. At this time if you do not set the
Src parameter, the Doppler effect will not be created, and no
effect sound will be output.
The effect is off when a value for the modulation source
specified for the Src parameter is smaller than 64, and
the effect is on when the value is 64 or higher. The
Doppler effect is triggered when the value changes
from 63 or smaller to 64 or higher.
f: Pitch Depth
With the Doppler effect, the pitch is raised when the sound
approaches, and the pitch is lowered when the sound goes
away. This parameter sets this pitch variation.
g: Pan Depth
This parameter sets the width of the stereo image of the
effect sound. With larger values, the sound seems to come
and go from much further away. With positive values, the
sound moves from left to right; with negative values, the
sound moves from right to left.
053: Scratch
This effect is applied by recording the input signal and
moving the modulation source. It simulates the sound of
scratches you can make using a turntable.
a
LFO Mode Loop, 1-Shot
Switches LFO operation mode
p.279
Src Off...Tempo
Selects the modulation source of
LFO reset p.279
b LFO Sync Off, On
Switches between LFO reset on
and off when LFO Mode is set to
Loop p.279
c
LFO
Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO p.259
Src Off...Tempo
Selects a modulation source for
LFO speed
Amt
–20.00...
+20.00
Sets the modulation amount of
LFO speed
d
MIDI Sync Off, On
When this is on, the LFO speed is
set by BPM, Base Note, and
Times, instead of Frequency
p.257
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo;
40–300 sets the tempo manually
for this individual effect p.257
Base Note ...
Selects the type of notes that
specify the LFO speed p.257
Times x1...x32
Sets the number of notes that
specify the LFO speed p.257
e
LFO Type
Individual,
Common1,
Common2
Selects either (individual) LFO,
Common FX LFO1, or Common
LFO2 p.257
Common
LFO Offset
[deg]
–180...+180
Sets the phase offset when Type
= Common 1 or Common 2
p.257
f
Pitch Depth 0...100
Sets the pitch variation of the
moving sound p.279
Src Off...Tempo
Selects the modulation source of
pitch variation
Amt –100...+100
Sets the modulation amount of
pitch variation
g
Pan Depth –100...+100
Sets the panning of the moving
sound p.279
Src Off...Tempo
Selects the modulation source of
panning
Amt –100...+100
Sets the modulation amount of
panning
h
Wet/Dry
Dry,
1 : 99...99 : 1,
Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Pan Depth
D
-mod
+
Trigger
LFO Mode = 1-Shot
Doppler
LFO
a
Scratch
Source
Off...Tempo
Selects the modulation source
for simulation control p.280
b Response 0...100
Sets the speed of the response
to the Scratch Src p.280
c
Envelope
Select
D-mod, Input
Selects whether the start and
end of recording is controlled via
the modulation source or the
input signal level p.280
Src Off...Tempo
Selects the modulation source
that controls recording when
Envelope Select is set to D-mod
p.280
Pitch
Higher
Doppler - Pitch / Pan Depth
Lower
Original Pitch
Left
Center
Right
Pitch Depth
Pan Depth
< < < < < <<<<<< >>>>>> > > > > >
VolumeLouder
Louder
Pan Depth
= (–) value
Pan Depth
= (+) value
Input
D-mod
Envelope Select
D
-mod
Envelope Control
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Scratch
Direct
Mix
D
-mod
Rec Control
Scratch
To Next Page
Loading...
