270
h: Feedback
Sets the feedback amount of the chorus block. Increasing the
feedback will allow you to use the effect as a flanger.
034: St. Biphase Mod.
(Stereo
Biphase Modulation)
This stereo chorus effect adds two different LFOs together.
You can set the Frequency and Depth parameters for each
LFO individually. Depending on the setting of these LFOs,
very complex waveforms will create an analog‐type,
unstable modulated sound.
035: Multitap Cho/Delay
(Multitap Chorus/Delay)
This effect has four chorus blocks with a different LFO
phase. You can create a complex stereo image by setting
each block’s delay time, depth, output level, and pan
individually. You can also fix some of the chorus blocks to
combine the chorus and delay effects.
a
LFO1
Waveform
Triangle, Sine Selects LFO1 waveform
LFO2
Waveform
Triangle, Sine Selects LFO2 waveform
Phase Sw
0 deg,
180 deg
Switches the LFO phase
difference between left and right
b
LFO1
Frequency
[Hz]
0.02...30.00 Sets the LFO1 speed
Src Off...Tempo
Selects the modulation source of
LFO1&2 speed
LFO1 Amt
–30.00...
+30.00
Sets the modulation amount of
LFO1 speed
c
LFO2
Frequency
[Hz]
0.02...30.00 Sets the LFO2 speed
Amt
–30.00...
+30.00
Sets the modulation amount of
LFO2 speed
d
LFO1 Type
Individual,
Common1,
Common2
Selects either (individual) LFO,
Common FX LFO1, or Common
LFO2 p.257
Common
LFO Offset
[deg]
–180...+180
Sets the phase offset when LFO1
Type = Common 1 or Common 2
p.257
e
LFO2 Type
Individual,
Common1,
Common2
Selects either (individual) LFO,
Common FX LFO1, or Common
LFO2 p.257
Common
LFO Offset
[deg]
–180...+180
Sets the phase offset when LFO2
Type = Common 1 or Common 2
p.257
f
Depth1 0...100
Sets the depth of LFO1
modulation
Src Off...Tempo
Selects the modulation source of
LFO1&2 modulation depth
Amt –100...+100
Sets the modulation amount of
LFO1 modulation depth
g
Depth2 0...100
Sets the depth of LFO2
modulation
Amt –100...+100
Sets the modulation amount of
LFO2 modulation depth
h
L Pre Delay
[msec]
0.0...50.0
Sets the delay time for the left
channel p.268
R Pre Delay
[msec]
0.0...50.0
Sets the delay time for the right
channel p.268
i
Feedback –100...+100
Sets the feedback amount
p.270
High Damp
[%]
0...100
Sets the damping amount in the
high range
Chorus/Flanger
Left
Right
Feedback
180 [degree]
Wet / Dry
Wet / Dry
High Damp
Stereo In - Stereo Out
LFO1: Tri / Sine
LFO2: Tri / Sine
Chorus/Flanger
High Damp
j
Wet/Dry
–Wet...
–1 : 99, Dry,
1 : 99...Wet
Sets the balance between the
effect and the dry input
p.259
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
a
LFO
Frequency
[Hz]
0.02...13.00 Sets the speed of the LFO
b
LFO Type
Individual,
Common1,
Common2
Selects either (individual) LFO,
Common FX LFO1, or Common
LFO2 p.257
Common
LFO Offset
[deg]
–180...+180
Sets the phase offset when Type
= Common 1 or Common 2
p.257
c
Tap1 (000)
[msec]
0...1000
Sets the Tap1 (LFO phase=0
degrees) delay time
Depth 0...30 Sets the Tap1 chorus depth
Level 0...30 Sets the Tap1 output level
Pan
L6...L1, C,
R1...R6
Sets the Tap1 stereo image
d
Tap2 (180)
[msec]
0...1000
Sets the Tap2 (LFO phase=180
degrees) delay time
Depth 0...30 Sets the Tap2 chorus depth
Level 0...30 Sets the Tap2 output level
Pan
L6...L1, C,
R1...R6
Sets the Tap2 stereo image
e
Tap3 (090)
[msec]
0...1000
Sets the Tap3 (LFO phase=90
degrees) delay time
Depth 0...30 Sets the Tap3 chorus depth
Level 0...30 Sets the Tap3 output level
Pan
L6...L1, C,
R1...R6
Sets the Tap3 stereo image
f
Tap4 (270)
[msec]
0...1000
Sets the Tap4 (LFO phase=270
degrees) delay time
Depth 0...30 Sets the Tap4 chorus depth
Level 0...30 Sets the Tap4 output level
Pan
L6...L1, C,
R1...R6
Sets the Tap4 stereo image
LFO1
LFO2
Bi-Phase Modulation LFO
Depth1
Depth2
+
Left
Right
Feedback
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Level
Level
Level
Level
Pan
Pan
Pan
Pan
LFO: Triangle
Tap1 Delay
Tap2 Delay
Tap3 Delay
Tap4 Delay
0 [degree]
180 [degree]
90 [degree]
270 [degree]
To Next Page
Loading...
