268
Chorus, Flanger, and Phaser (Cho/Fln Phaser)
029: Stereo Chorus
This effect adds thickness and warmth to the sound by
modulating the delay time of the input signal. You can add
spread to the sound by offsetting the phase of the left and
right LFOs from each other.
e: L Pre Delay [msec]
e: R Pre Delay [msec]
Setting the left and right delay time individually allows you
to control the stereo image.
030: Vintage Chorus
This models a famous chorus unit that was built into a
guitar amp. Although it does not provide a chorus and
vibrato select switch, you can use the Wet/Dry setting to
produce their effect. The Speed, Depth, and Manual
parameters allow an even wider range of sounds than the
original unit.
e: Wet/Dry
d: Output Mode
For the master effects, Wet/Dry adjusts the output level of
the effect sound.
When Output Mode is Mono, L and R will output the same
vibrato effect. Normally, you’ll use the Wet/Dry setting to
mix the direct sound and processed sound so that a chorus
effect is produced. If you set this to Wet so that none of the
direct sound is included, you'll obtain a vibrato effect.
If Output Mode is ST (L‐D&R‐W), the direct sound will be
panned to L, and the effect sound will be panned to R for
output. Normally, you’ll use the Wet/Dry setting to mix the
direct sound and processed sound, producing a chorus
effect on only the R‐channel, and creating a spacious stereo
effect that extends to the left and right. If you set this to Wet,
and pan the direct and processed sounds to left and right,
and then output them to stereo speakers, the direct sound
and processed sound will be mixed in the air, producing a
chorus effect with spacious clarity.
a
LFO
Waveform
Triangle, Sine Selects the LFO Waveform
LFO Phase
[degree]
–180...+180
Sets the LFO phase difference
between the left and right
p.259
b
LFO
Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO p.259
Src Off...Tempo
Selects a modulation source for
LFO speed
Amt
–20.00...
+20.00
Sets the modulation amount of
LFO speed
c
MIDI Sync Off, On
When this is on, the LFO speed is
set by BPM, Base Note, and
Times, instead of Frequency
p.257
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo;
40–300 sets the tempo manually
for this individual effect p.257
Base Note ...
Selects the type of notes that
specify the LFO speed p.257
Times x1...x32
Sets the number of notes that
specify the LFO speed p.257
d
LFO Type
Individual,
Common1,
Common2
Selects either (individual) LFO,
Common FX LFO1, or Common
LFO2 p.257
Common
LFO Offset
[deg]
–180...+180
Sets the phase offset when Type
= Common 1 or Common 2
p.257
e
L Pre Delay
[msec]
0.0...50.0
Sets the delay time for the left
channel p.268
R Pre Delay
[msec]
0.0...50.0
Sets the delay time for the right
channel p.268
f
Depth 0...100
Sets the depth of LFO
modulation
Src Off...Tempo
Selects the modulation source
for the LFO modulation depth
Amt –100...+100
Sets the modulation amount of
the LFO modulation depth
g EQ Trim 0...100 Sets the EQ input level
h
Pre LEQ Fc
Low,
Mid-Low
Selects the cutoff frequency (low
or mid-low) of the low-range
equalizer
Pre HEQ Fc
High,
Mid-High
Selects the cutoff frequency
(high or mid-high) of the high-
range equalizer
i
Pre LEQ Gain
[dB]
–15.0...+15.0 Sets the gain of the Low EQ
Pre HEQ Gain
[dB]
–15.0...+15.0 Sets the gain of the High EQ
j
Wet/Dry
–W
et..
.
–1 : 99, Dry,
1 : 99...Wet
Sets the balance between the
effect and the dry input
p.259
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
Chorus
Chorus
Left
Right
LFO Phase
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
EQ Trim
EQ Trim
LEQ
HEQ
LEQ
HEQ
LFO: Tri / Sine
a
Speed [Hz] 0.10...10.0 Sets the speed of LFO
Src Off...Tempo
Selects a modulation source for
Speed [Hz]
Amt –100...+100
Sets the modulation amount for
Speed [Hz]
b
Depth 0...100 Sets the modulation depth
Src Off...Tempo
Selects a modulation source for
Depth
Amt –100...+100
Sets the modulation amount for
Depth
c Manual 1...100 Sets the sweep frequency
d Output Mode
0: Mono,
1: ST (L-D&R-W)
Sets the outpu mode
e
Wet/Dry
Dry, 1:99 ...
99:1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100 ... +100
Sets the modulation amount for
Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Chorus
LFO
Output Mode
Mono
Stereo
(L-D&R-W)
To Next Page
Loading...
