Sequencer mode
114
0–5: Arpeggiator A,
0–6: Arpeggiator B
Here, you can make arpeggiator settings for the song. A
song can run two arpeggiators simultaneously.
Arpeggiator parameters can be edited in P7: Arpeggiator/
Drum Track, but certain major parameters can be edited in
these pages as well. You can edit these parameters in
realtime, for example by changing the arpeggio pattern
while playing in Sequencer P0–1:Play/REC.
You can also use the TEMPO knob and the arpeggio control
(ARP) GATE knob, VELOCITY knob, SWING knob, and
STEP knob to control the arpeggiator in realtime.
0–5(6)a: Track Select, Tempo, RPPR
Track Select [Track01…16, Master Track]
(Tempo) [040.00…300.00, EXT]
RPPR [Off, On]
Here, you can select the track, specify the tempo that will
control the song or arpeggiator etc., and turn RPPR on/off.
For more information, please see “0–1(2)a: Location, Meter,
Tempo, Tempo Mode, Song Select, Track Select, Reso, RPPR”
on page 109.
0–5(6)b: Arp Controls
This shows the value of each parameter for the ARP
assignments of the REALTIME CONTROL knobs. The
arpeggio controls allow you to use the four knobs to control
the two arpeggiators in real time.
[GATE] [–64...+00...+63]
[VEL.](Velocity) [–64...+00...+63]
[SWING] [–64...+00...+63]
see p.54, p.121
[STEP] [–64...+00...+63]
see p.121
0–5(6)c: Arpeggiator Run, Track assign
Arpeggiator Run A, B
When the ARP button is on, the arpeggiator(s) you checked
here will run if they are assigned to a timbre by Arpeggiator
Assign (7–1(2)c).
When the arpeggiator is on, these check boxes let you turn A
and B on/off.
This parameter can also be set from P7: ARP/DT page
Arpeggiator Run A, B.
Track assign
This indicates the arpeggiator A and B assignment status for
each track 1–8. These settings are made in Arpeggiator
Assign (Seq 7–1(2)c).
0–5(6)d: Arpeggiator A (B)
Pat (Pattern)
[P0...P4, U0000(INT)...U0899(INT),
U0900(USER)...U1027(USER)]
Octave [1, 2, 3, 4]
Reso (Resolution) [
, , , , , , , ]
Sort [Off, On]
Latch [Off, On]
Key Sync. [Off, On]
Keyboard [Off, On]
Arpeggio Pattern Preview
Set the various parameters of the combination arpeggiator.
For more information, please see “COMBI P7: ARP/DT
(Arpeggiator/Drum Track)” on page 91.
These parameters can also be set from 7–3(4): Arpeggiator
A(B) Setup.
V
0–5(6): Menu Command
•0: Memory Status see p. 163
•1: Exclusive Solo see p. 64
•2: Rename Song see p. 163
•3: Delete Song see p. 163
•4: Copy From Song see p. 163
•5: Load Template Song see p. 163
•6: Save Template Song (Save as User Template Song)
see p. 164
•7: FF/REW Speed see p. 164
•8: Set Location (Set Location for Locate Key) see p. 164
•9: GM Initialize see p. 165
•10:
Copy from Combination
see p. 166
• 11: Copy from Program see p. 167
• 12: Copy Arpeggiator see p. 167
For more information, please see “Sequencer: Menu
Command” on page 163.
0–5c
0–5d
0–5a
0–5
Menu
0–5b
To Next Page
Loading...
