Korg Krome - Page 62

Program mode
54
Resolution* [ ,  ,   ,  ,   ,  ,   ,  ]
Specifies the timing resolution of the arpeggio. The notes of
the arpeggio will be played at the interval you specify:  ,  ,
  ,  ,  ,  ,   , or  . The speed of the arpeggio pattern is
determined by the Arpeggiator  (Tempo) and the
Resolution.
Turning the arpeggio control ARP STEP knob toward the
right will shorten the spacing of the arpeggiated notes
(Resolution) in increments of halving the spacing. Turning
the knob toward the left will shorten the length of the
pattern (Length) in increments of halving the length. When
the knob is in the center position (12 o'clock), the values will
be as specified by the Length and Resolution settings
(Global P6: Arpeggio Pattern‐ Setup page).
Gate [000...100(%), Step]
Specifies the length (gate time) of each note in the arpeggio.
000–100(%): Each note will be played with the specified gate
time.
Step: This is available when a user arpeggio pattern
U0000(INT)–U1027(USER) is selected for Pattern. When
this is selected, the gate time specified for each step will be
used.
The gate time can also be controlled by the arpeggio control
(ARP) GATE knob. Rotating the knob toward the left will
shorten the gate time, and rotating it toward the right will
lengthen the gate time. When the knob is at the 12 o’clock
position, the gate time will be as specified here.
Velocity [001...127, Key, Step]
Specifies the velocity of the notes in the arpeggio.
001–127: Each note will sound with the specified velocity
value.
Key: Each note will sound with the velocity value at which it
was actually played.
Step: This is available when an user arpeggio pattern
U0000(INT)–U1027(USER) is selected for Pattern. When
this is selected, the velocity specified for each step will be
used.
The velocity can also be controlled by the arpeggio control
(ARP) VELOCITY knob. Rotating the knob toward the left
will decrease the velocity, and rotating it toward the right
will increase the velocity. When the knob is at the 12 o’clock
position, the velocity will be as specified here.
When a preload user arpeggio pattern is selected, setting the
Gate or Vel oc it y to Step will add a sense of groove to the
arpeggio pattern.
Swing [–100...+100(%)]
This parameter shifts the timing of the odd‐numbered notes
of the arpeggio.
This can also be controlled by the arpeggio control (ARP)
SWING knob. Turning the knob toward the left will adjust
the timing in the “‐” direction, and turning it toward the
right will adjust the timing in the “+” direction.
Sort* [Off, On]
This specifies the order in which the notes you press will be
arpeggiated.
On (checked): Notes will be arpeggiated in the order of their
pitch, regardless of the order in which you pressed them.
Off (unchecked): Notes will be arpeggiated in the order in
which you pressed them.
Latch* [Off, On]
Specifies whether or not the arpeggio will continue playing
after you take your hand off of the keyboard.
On (checked): The arpeggio will continue playing after you
remove your hand from the keyboard.
Off (unchecked): The arpeggio will stop when you remove
your hand from the keyboard.
Key Sync.* [Off, On]
Specifies whether the arpeggio pattern will begin when you
press a key, or whether it will always follow the  (Tempo)
(Prog 0–1a).
On (checked): The arpeggio pattern will start playing from
the beginning when a note‐on occurs from a condition
where no keys are pressed. This setting is suitable when you
are playing in realtime and want the arpeggio to play from
the beginning of the measure.
Off (unchecked): The arpeggio pattern will always play
according to the  (Tempo).
Keyboard* [Off, On]
This specifies whether the notes you play on the keyboard
will be sounded as usual in addition to being sounded as
part of the arpeggio.
On (checked): The notes you play will be sounded on their
own, in addition to being sounded as part of the arpeggio.
For example if you simultaneously press two or more notes,
they will be sounded as usual in addition to being played as
arpeggiated notes.
Off (unchecked): Only the arpeggiated notes will be heard.
Note: You can use the menu command Copy Arpeggiator to
copy arpeggiator settings from another program or
combination (see page 66).
Arpeggio Pattern Preview
This shows a graphic of the steps of the user arpeggio
pattern.
V 7–1: Menu Command
•0: Write Program see p. 64
•1: Exclusive Solo see p. 64
•2: Auto Song Setup see p. 65
•3: Copy Arpeggiator see p. 66
For more information, please see “Program: Menu
Command” on page 64.
Octave: 4
UP
Step
123456789
Swing
–50 –25 +25 +50
When Resolution =
ON, UP
Sort
OFF, UP
Sort