Korg Krome - 188: L;C;R Long Delay; 189: St;Cross Long Delay (Stereo;Cross Long Delay)

334
a: Sw
This parameter determines how to switch on/off the
overdrive via a modulation source.
When Sw = Toggle, overdrive is turned on/off each time the
pedal or joystick is operated.
Overdrive will be switched on/off each time the value
of the modulation source exceeds 64.
When Sw = Moment, overdrive is applied only when you
press the pedal or operate the joystick.
Only when the value for the modulation source is 64 or
higher, the overdrive effect is applied.
188: L/C/R Long Delay
This multitap delay outputs three Tap signals to left, right
and center respectively. You can set a maximum of
5,460msec for the delay time.
189: St/Cross Long Delay
(Stereo/Cross Long Delay)
This is a stereo delay, and can by used as a cross‐feedback
delay effect in which the delay sounds cross over between
left and right by changing the feedback routing. You can set
a maximum of 2,730msec for the delay time.
a
L Delay Time
[msec]
0...5460 Sets the delay time of TapL
Level 0...50 Sets the output level of TapL
b
C Delay Time
[msec]
0...5460 Sets the delay time of TapC
Level 0...50 Sets the output level of TapC
c
R Delay Time
[msec]
0...5460 Sets the delay time of TapR
Level 0...50 Sets the output level of TapR
d
Feedback
(C Delay)
–100...+100
Sets the feedback amount of
TapC
Src Off...Tempo
Selects the modulation source
for the TapC feedback
Amt –100...+100
Sets the modulation amount of
the TapC feedback
e
High Damp
[%]
0...100
Sets the damping amount in the
high range p.289
Low Damp
[%]
0...100
Sets the damping amount in the
low range p.289
f
Input Level
D-mod [%]
–100...+100
Sets the modulation amount of
the input level p.284
Src Off...Tempo
Selects the modulation source
for the input level p.284
g Spread 0...50
Sets the width of the stereo
image of the effect sound
p.289
h
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
C Delay
R Delay
Left
Right
Feedback
Spread
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Input Level D-mod
High Damp Low Damp
L Delay
Input Level D-mod
+
Level
Level
Level
a Stereo/Cross Stereo, Cross
Switches between stereo delay
and cross-feedback delay
b
L Delay Time
[msec]
0.0...2730.0
Sets the delay time for the left
channel
c
R Delay Time
[msec]
0.0...2730.0
Sets the delay time for the right
channel
d
L Feedback –100...+100
Sets the feedback amount for
the left channel
Src Off...Tempo
Selects the modulation source of
feedback amount
Amt –100...+100
Sets the modulation amount of
the left channel feedback
e
R Feedback –100...+100
Sets the feedback amount for
the right channel
Amt –100...+100
Sets the modulation amount of
the right channel feedback
f
High Damp
[%]
0...100
Sets the damping amount in the
high range p.289
g
Low Damp
[%]
0...100
Sets the damping amount in the
low range p.289
h
Input Level
D-mod [%]
–100...+100
Sets the modulation amount of
the input level p.284
Src Off...Tempo
Selects the modulation source
for the input level p.284
i Spread –50...+50
Sets the width of the stereo
image of the effect sound
p.289
j
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
Delay
Delay
Stereo/Cross
Left
Right
Feedback
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Input Level D-mod
Input Level D-mod
High Damp Low Damp
High Damp
Low Damp
Spread
Stereo/Cross